i did try my e8400 @ 4Ghz. at 1.304v
is that a bit high???

i try 1.25v bootable but only stable for few hours of orthos.

i only did simple changes in Bios...

AI Overclock: Manual
CPU Ratio: 9
FSB Strap: 445
The rest of the setting left Auto or as default.

Thanks for sharing, got difference angles of picture, very nice looking mobo

This post has been edited by aLWAYStHEsAME: Jul 16 2008, 01:32 AM

my Asus OCprofile cant save different voltage profile
why orr?

What motherboard and bios version you are using?

hmm anybody care to share combo of 9450 and rampage oc to 3.6 stable prime?

For Maximum II Formular user, you guys can apply this resolution to fix the thermal problem. It is in chinese. Hopes can get english version other place soon.

http://forum.coolaler.com/showthread.php?t=185186>

anyone here have p5e have successful flashed to maximus or rampage bios? can share out? thank

If you've the time then going thru this thread will give you an answer you're looking for. If not, just kindly PM ahsiah or cstkl for advice. They are the maestro here with ASUS board.

This post has been edited by skymyxe: Jul 18 2008, 02:52 PM

i really hope my next board will be from asus
but previous board disappoint me


This post has been edited by fesick: Jul 18 2008, 02:57 PM

ok, i will going thru tis thread when i free.. thx

i am new to overclocking , I just bough Asus P5Q deluxe, if I overclock my FSB, do I need to overclock my RAM also,cause I feel not need to overclock my value RAM.

d vcore is good.try to push higher ur FSB strap.should be no problm for P5Q duluxe.

If you overclock your CPU with FSB, you got to overclock your RAM too.

not true. well, not wrong either but it really depends on the RAM specs.

if you look at his rig, it's using E6750 with 1333Mhz FSB. on 1:1 FSB:RAM ratio the RAM will be operating at DDR2 667 speed.

so if the RAM is a DDR2 800 RAM. even overclocking the FSB to 1600Mhz on 1:1 FSB:RAM, the RAM will be operating at DDR2 800 speed which is only the default speed of the RAM.

in my case, i'm using DDR2 1066 RAM (yes, not kidding) so I really have to OC my processor to like what? 2000Mhz FSB already also still the run is running lower than it's default capable speed.

This post has been edited by goldfries: Jul 23 2008, 11:57 AM

i'm quite new to overclocking. just had some free time, so decided to try out some mild oc. same like daze, i did only minor changes in the bios, using AI overclock to 20%. so now my proc running at 2.4GHz and ram at DDR2 800. if i wanna push further what should i do? increase the fsb?

---

Added on July 24, 2008, 10:34 amjust tried again..unlink fsb and ddr frequency. tried increase fsb to 1066MHz. so now running at 2.66GHz. any steps to increse the oc?

This post has been edited by dlwl: Jul 24 2008, 10:39 AM

Asus Rampage Formula bios updated 0408

Personal experience
1. Memory stability improved.
2. Overclocking FSB increased.

Refer to the url below.

http://www.keepandshare.com/doc/view.php?id=712947&da=y

Please take note, I have test this only with Rampage Formula motherboard. For those with P5E flashed "Rampage Formula" or Maximus Formula owner, use it at your own risk.

now i learn it

ram divider.
1:1

eg. E2160 with 9X333 then the ram will be dual 333 as 667
eg. E2160 with 9X400 then the ram will be dual 400 as 800

1:1:20
eg. E2160 with 9X333 the ram will be dual 1.2X333 as 800
eg. E2160 with 9X400 the ram will be dual 1.2X400 as 960


when install a E2160 on board with default setting
eg. E2160 with 9X200.. board will check ram module u install

suppose using DDR2-800
it will automatic change to 1:2

corrent me if i am wrong.

any1 use p5n32 e sli plus here??

M3A32MVP-DELUXE WiFi AP
bios 1002

can anyone tell me, what's the problem when the CPU gets error in the stress test?