listen from the experienced one, guys

it stated 3.4GHz because it still read ur multiplier as x9....
4pin atx can be use at 8pin eps...but it will give a little instability...
that's y the 4 pin molex can help u patch up voltage if needed...better just connect it...
1.5v is ur selecting voltage in bios??or by plugin the 4pin molex make it 1.5v??? which mean u cannot do nothing

if not later on u were unlucky...then hav to use the guide at my siggy...

This post has been edited by flatfinger: Mar 4 2008, 05:10 PM

I set it in bios,not stable below 1.5V
9x380mhz is what i want but i only get 8x380 or 9x340.
if i un-plug 4-pin molex 1.5v also not stable.Does any one who use ip35-e also facing the same problem?

just plug in the 4 pin molex...
for 9x380...u will need more than 1.5v to stable lor....1.5v not enough...only can boot but will failed orthos for sure...

@tech_frix
Yeah bro i know tht...
Havent updated frm rev 13 to 14 yet...wat happened to ure board? ok ad tech_frix bro?

This post has been edited by Bigblock: Mar 4 2008, 05:20 PM

1.5V no enough?
i thought 1.5V is consider too high already for a C2D bas proc...
most c2D only need 1.35/1.45V to reach 3.4ghz.

@all
hold on your horses guys.. thanks commanders under my legion, flattie, techfrix for guiding this fellas.. but there are few points i would like to state

1. For the Abit ip35-e, i dont recommend a 4 pin PSU, coz its unstable. Play with 8 pins.

2.BIOS 14 is alright. so use it. and dont dream of 3.4GHz yet. Start your first benchmark at 3.2Ghz. Listen, 3.4Ghz is not easy, even for my self.

And Funnyface, we are not talking about Conroes here, we are talking about Allendales with a stock speed of 1.6-1.8Ghz, so u will at least need 1.48V(for the normal procs) to be running at 3.4Ghz, attempting the 8* of course. But if u do go at 9*, then maybe... but very unlikely.

using x9....u wont get it if u set 1.5v in bios...u must consider about the vdrop n vdroop...to get 3.4GHz stable u must at least have steady state vdroop at 1.5v...which mean u need to set higher than it to get that value...
@1.5v u only can get 3.3GHz stable if ur setting is rite...

yes indeed...

This post has been edited by flatfinger: Mar 4 2008, 07:13 PM

i agree with flattie(you dont mind me calling u rite, this nick, too much aus la ) ) u have to play very high voltages. 3.4Ghz is very syok to play with

How do you guys do Orthos on 3.4Ghz? I am getting temps close to 70C while on 3.4GHz...

get better cooling or just get a better board which gives u a lower Vdroop, bro.

hehehe...after a hard and crucial work, my mobo revive from d dead...
so my mobo had died once so now dia dah jadi makin powah!!!
so bear in mind when flashing or updating ur bios...
just retire from OC for a while...stick to default speed...
bz with work and dont have time play games..

haha, i remember techie was so scared and flattie saved him from an RMA.. why la techie, u should not retire, you have potential

actually i did it my style and dont ask me how cuz will spoilt d mobo!!!
hint, bios chip...
potential????perli ka???
heheheh...wanna kerja kuat for my nest GC...9600gt or 3870!!!

go for the 3870 instead. coz from my sources, its really far from the 8800gt performance. I am not perli you la. i m serious. Like me, soon ill retire so i need a few people here to run all this la. To teach and all.

dats y lor..3870 plak dah turun harga...
sapphire for rm670...quite tempting rite??
waa...wanna retire again??hehehe..
getting married i presume??

retiring for research on extreme computing bro. Not ready to marry yet. But yes someones on my mind and hmm shes nice. By the way bro, u should get the hd 3870 if u do have the means and try it.

HD 3870 not bad, if got chance grab it and give it a go.

Don't say retire, say "going for holiday"

By the way, I'm running ORTHOS now at priority 9... Everything is so freaking slow

Bro i hav booted up at 3Ghz 333*9 but i had to increase voltage to 1.4...wah...then nie stable..
Lesser than tht it can boot but will fail orthos and OCCT...
i plan to wach at 3Ghz nie
I tried 380*8 also not stable...bad proc ker?
I need better config to be able to run my 667 tracer at 800Mhz
I hav never tried more than 3Ghz yet

This post has been edited by Bigblock: Mar 4 2008, 10:53 PM