If you trade-in your old car can get within 1-2 months from my own experience

may i know if i buy a used car which the seller did not send the car to service centre all these while. Can i still claim for warranty for door lock and sensor issue? Also can i continue the warranty by Perodua issuing me a new service booklet? Is it possible?

I noticed that auto gear oil and engine oil sold outside spare parts shop are way more than Perodua. 1 litre of ATF cost around RM45 whereas perodua only selling RM36.
Engine oil also expensive at outside.

The best part is you may buy oil and parts from perodua and service your car at any outside car workshop. Provided your car is no more warranty.

Hi, I have installed Ultra Racing stage 2(Front and rear anti-roll bar) on my car and observed better stability when turning and cornering.

Therer are some members here upgrading the rim and Tyres from 14 to 15. Is it advisable to do it for even more stability?

Thanks in advance

usually change rim tyre before doing bar. done ady no issue.
15 is very recommended size

i was from 15 change back to 14". I find 15 too noisy and fuel consumption is more. 14" makes the car lighter and quieter on the road.

My Bezza having weird issue with the brake light won't off after on, even when i off the engine. I have change the switch stop lamp with new one by the brake pedal but issue still persist.
I'm very sure the switch button is fully press by the pedal. The only way for it to off is to unplug the wire from the switch.

I have used a multi meter to test the switch 4 connection point for both new and old switch with both working same. The old switch button spring is still very firm, work same as the new one.



Connection Point 1 & 2 got current and 3 & 4 no current when switch press.
Connection Point 3 & 4 got current and 1 & 2 no current when switch release.

I'm not sure above is the correct working way for the switch, since the problem persist.

brake light can operate even enjin off. this applicable to every brands very normal.
whats not right is the position of switch actuator.
theres few easy way fo test. urs is push start button or turn key

Bezza 1.3 , Push start button.

able start enjin without step on brake (lights on) ?

Yes as long the light is on will start. Lights off wont start.

The serious problem is when i'm driving the car on road people driving behind me keep seeing the brake light on all the time.

The car is also not accelerate smooth when climbing hill felt abit jerking when the brake light in on when driving. I feel the Car ECU or ECM is detecting the the braking causing the car not accelerate smoothly.
If the brake light is not on the car drive no issue.

The crazy part is if i'm driving the car on road in slow moving motion and i disconnect and reconnect the switch stop cable the gas peddle will lost acceleration for a few second.

yes brake will affect gas pedal. so can you adjust switch position shift closer to brake pedal?
it is nc action so terbalik logic

This post has been edited by ktek: Oct 16 2023, 11:34 PM

Not the switch position issue as i have fully push it down to the max point & the button is fully press all the way with no gap when brake pedal not step. I even try using my finger pressing the button still the brake light on.

This post has been edited by DEz012: Oct 16 2023, 11:55 PM

Hi guys,got a question. The bezza I bought is in 2017 advance version. But now the reverse camera cannot be used anymore.

Wondering if I buy those reverse camera from shoppe, can it be connected to the existing screen. Will it work?

Can loh , go youtube check how to DIY

Wondering if anyone fuel consumption for their have changed throughout the years.Bought my car since launch and now my full tank is 440km instead of 500/480km when bought.Is that normal fuel consumption due to aging?

check obd status for long/ short fuel trim

Fuel trims seems fine , stft hover on below negative 5 and ltft max figure 3.1% during idle.Miss fire count was 0 as well. Btw thanks for informing me new things haha

good condition wor. worry is gearbox slip

Diddint experience any slippage at all , only know that due cold start I need let my engine run a few seconds when change my gearbox to D for smooth changing if not it will be a bit rough. However , forgot to mention that my rear absorber need to change but my question was is my reduction in FC normal based on my car years of close to 8 years d in 2 months