practice practice practice .. but of coz practice the correct thing la .. hahaha
as long as u enjoy flying whatever however then its ok liau lorr

me NEWBIE oso laaa .. flying 3 months or so only

No one teach me how to fly correctly wor...
Hahahahaha... So hantam only lor...
Still enjoy flying eventhou crash so damn much...

ya ... most important is ENJOY !!!
crash is part of the game .. tell me who play rc heli never crash b4 .. hahaha

You lor...

i got crash b4 laa .. 450PR0 crash b4 liau maaa
the 4G3 damm kow alot of crashes ... compy not yet laa .. hehehe
my bigger helis so far only 1 crash .. have to be very JIMATS coz poor ppl like me cannot afford to simply crash one maa

NO CRASH NO IMPROVEMENT!

Hahaha... Crash too much also not good...

crash too much straightaway surrender give up dont wanna play anymore .. hahahhahaa

Check the connection and seem ok. I just noticed that the main motor is run hotter than usual and it spin slower than the tail motor causing the tail always spin to the left so I have to adjust the trimmer. Now my heli got wagging and motor run slower so which part really giving problem.......Motor? esc? 4 in 1? Not cheap to buy all those part.....

motor running slower and slower ??
check see pinion too tight or not .. main gear should be able to spin easily when u tilt the heli with the blades all to ONE side
check see pinion loose or not
if loose then remove pinion .. put some locktite and put pinion back .. let it sit for 20-30mins .. then only spool up
if pinion ok then time for new motor liau .. hahahaha
u dont have to buy the walkera motor .. u can get similar motor from hobbycity .. tail motor oso u can get from hobby city

how come your motor can wear out so fast one ?? my walkera brushless still running good .. of coz 2nd one liau la ... 1st one kondem liau due to crash too much i think .. hehehehe

these small little helis are fun indoors but their electrical parts leaves more to be desired .. thats the main weakness of walkera
but even my 450PRO oso i feel the motor starting to lose some power liau compared to new .. its still running very fast laa but can feel

---

Added on September 19, 2009, 7:18 amwagging normally indicates vibration or gyro gain set too high ..
vibration can be caused by alot of things .. u will have to slow slow troubleshoot liau .. i suspect your tail since u say the front and head parts no vibs >> wires very still when spool up

This post has been edited by QiW: Sep 19 2009, 07:18 AM

Wah Qiw really sifu liao in repairing micro heli...
Can provide alot's of advice and troubleshooting guide for newbies..

ya .. thats coz i crash alot maa .. so repair alot lorr .. hahahaha

damn...
my servo keep binding...
bored...
got fly later? i need sifu to tune

flying tomoro morning at BTHO ... u know the place ??

Pinion no tight, blade spin easily....Take out the main motor, check pinion ur loose bor?...no loose....assembled back....Try to fly after reassemble the motor.....problem still there....

I also crash too much mah....so motor gone lor....Can provide hobbycity website and which one shall I get? No need to change the ESC? This motor better than walkera one arrr?

this one should suit u .. http://www.hobbycity.com/hobbycity/store/u...r_Motor_10300kv

similar to walkera ori brushless .. only cheaper .. hahaha

---

Added on September 19, 2009, 10:53 pmjust in case u cannot find BTHO .. the X is the exact spot we normally fly at laaa
http://wikimapia.org/#lat=3.04474&lon=101....74&z=16&l=0&m=b

This post has been edited by QiW: Sep 19 2009, 10:53 PM

i just reach home from friends house...
see how le.. wake up i call u

Wow, is so cheap...only RM30! but shipping cost seem expensive.

I just realized that the trimming pot on the RX2406B receiver is a gyro sensitivity instead of servo extend sensitivity . The old 4#3b RX2406 is build with servo extend sensitivity and do not have gyro sensitivity adjustment. I never tune the gyro pot since I got the heli....haha.....Do you think by adjusting the pot, it will reduce or solve the wagging issue?

Will going out for dim sum, come back then will try to play around with the pot.

reducing gyro sensitivity of coz will reduce tail wagging laa .. aiyooooooooooo
so good life got dimsum session ... me just eat half boiled eggs only .. save $$$ play heli .. hehehe

---

Added on September 20, 2009, 7:29 amthis fren must be a FEMALE liau laa .. hehehe

This post has been edited by QiW: Sep 20 2009, 07:29 AM

Yesterday night just finished the direct servo mod for the belt-cp, still don't have extra RX for it, so not in rush to complete the project~
Tonight after work will continue with the servo linkage arm.


Attached thumbnail(s)