Tornado goes up to 300W

Now where's my spare truck battery??

Scared i'll get drowned by 300W vapes. lol

Majilis perbandaran hasn't fogged my area for some time...hoping my DIY citrus extract fog will shoo away mosquitos...public service vaping

Err... As long as it doesn't become this:





This post has been edited by Eiraku: Jul 5 2016, 02:37 PM

Naah...it'll never be as bad as smog from Indonesia.

I think George Lucas was prophetic, calling them Jawas

On another note - what drip tips is good to couple with the Serpent Mini?
Anything from FT?

I don't own a serpent mini, used a friend's unit with my own drip tip ( https://www.fasttech.com/products/1546312 ), and I think it's better because the stock drip tip is a bit short.

Looks-wise, it matches the atty. The bore (5mm) is the same as the stock DT. Minor con: only has 1 o-ring, but it's not loose nor does it pop out easily. Because it has only 1 o-ring, it will have some give, and lean to one side when sufficient horizontal pressure is applied. Bad if u don't like a DT that can move a bit, good if u accidentally hit a tooth while talking a toke.

Why not my current fave DT: The GMv2's "swirl flow" tip. Sounds like completely gimmicky BS... and yet I get far less spitback on these then I do on a normal smoothbore DT. More flavour too, though I might just be imagining things.

Plus, double o-rings so it's secure as eff. It cheap too, and there's a black one if you want.

That said, it is a single cast SS DT, so if you overtoke a hot build with it, the tip *will* get rather toasty. Also the "rifiling" can be a PITA to clean lol.

Check it out here (FT): https://goo.gl/7RW8VP

The Fodi's hybrid acrylic DTs is a nice alternative, but a tad more spitbacky (smoothbore) and single o-ring only. The hybrid construction is pretty good at protecting your lips from heat though.

Linky here (FT): https://goo.gl/6HQ3m7

This post has been edited by Eiraku: Jul 5 2016, 05:38 PM

Looks ok but its out of stock and still has a wide bore.
Got to hunt for a smaller bore.

3mm bore (but shorter, and in stock) https://www.fasttech.com/products/0/1001911...el-510-drip-tip

It's a bit too restrictive for me, but may suit u.

Added to cart - thanks

BTW it says 19mm - I wonder what size is the Serpent opening

19mm is the height of the driptip, no bearing on, or interaction with any openings in the atty. The serpent's topcap takes standard 510 driptips; this driptip's base outer diameter is 8.5mm...it'll fit.

Noted that
Thanks

https://www.fasttech.com/products/3792304
Currently using.

Pros:
Dotmod DT clone, turns a few heads to those whom never seen the authentic up close.
Wide Bore.
Friction Fit.
Looks just like the authentic.

Cons:
Slightly too tall for the serpent mini and leaves a 1mm ish gap/hang.

Anywhere to buy efusion mini in kl.
Been looking for awhile

so got myself a tfv4 last couple of week, dont ask me why not get the tfv8.

the thing is the taste is severly muted in the tank. The same juice taste so much better on my subtank and tobeco turbo v2 rda.(duhh RDA )

on the R1, my build is 0.6 firing at 28-30w

on the R2, my build is 0.25 firing at 40 - 42 W.

fog machine all right, but juice is muted.

should have gotten a griffin 25. test drive a friends and i was shocked how good it taste, thoug vapor felt wet

all build was on 24 kanthal a1.

same...no matter how i wicking...flavor always muted..yes its a fog machine...but even using ss316 space...flavor wasn't there

yeahh man, i hope anyone here that is enjoying the tank can point out what i did wrong, and since the tank have been out so long already.

No leaking or whatever problem. Got dry hit on my first tank of juice, learn the lesson wick properly its been fine now,

just the flavor.

Pull the coil higher. The airflow is too much. The coils meant to be big on this tank as well. 3mm is bare minimum.