i normally use 1.2ohm coil,.. but after few refill,.. it'll go up to 1.4 or sometimes 1.5,..

and i use the lowest wattage,.. 6 watt,. lesser smoke, but save fluid and battery,..

why use so low ohm ???.. if short circuit dangerous oh... higher ohm safer..

https://www.google.com/search?q=KKM+vape&ie...+vape&tbs=qdr:w

Should be ok since Kbox Mini package come with OCC 0.5-0.6ohm i guess, just need to check recommended wattage for it

0.5ohm is not that low by today's standard imo

i just read recent news with statement from KKM saying that 1 day vaping equal to 150 cig sticks, and vape produces more harmful chemical than normal cig.. basically KKM is saying better smoke than vaping.. BULLSHIT.. why there is more moron than normal people in this country

This post has been edited by hallucinogen: Dec 14 2015, 04:44 PM

it's a heating device,.. not electronics,..

Mech Mod 101

Learn/Read on battery safety and ohms law before using mechs.
"V=IR"
ALWAYS know your battery rating and limits.
DONT use cheapo/china/rewrapped batteries and dont over discharge your batteries.
INVEST on a reliable and accurate ohm reader.
Protruding 510 pin is a MUST when using hybrid connections.

Only build according to your battery rating and always leave some headroom for safety.
Always calculate that you are using a fully charged battery at 4.2V to know the maximum amperage your build will draw.
A fully charged battery with a 0.2 build will be draw 21A, HE4, HG2 & 25R are only rated for 20A and therefore cannot be used for a build this low on a mech.

I only use 30A Sony VCT4 and VCT5 for mechs, VCT4 has less capacity at 2100mah but has a lower internal resistance and hits harder when compared to a VCT5 with 2600mah.

Please be safe when using a mech, i know some idiots that trust their lives on a efest battery with a 0.1 build.

Even if you fire 50w with a 0.3 build on your kbox you'll be only drawing 13A the most.

How would it short circuit unless there is something physically done to it? A short at 0.3 or 1.2 is the same, now a battery that vents is a different story

yes.. with subohm everywhere... 0.5 is consider high...

low resistance are prone to current hike,.. high resistance wud burn on high current, hence good for safety measure..

ain't higher resistance give higher heat ??..

opposite, bro... higher resistance lower hear... lower resistance higher heat... so, somewhere near 0.5ohm is consider safe for regulated mod.. I coil around 0.4-0.6 all the time... just nice...

btw... how can u vape at 6watt? my side, minimum 15watt... maximum 30watt... 6watt not going to get u the flavour real taste for sure...

If u knew how many snubbies I actually use daily, u'd think me mad...so let's leave it at 3

If you want to compare the snubnose to derringer, you'll have to ask yourself what u prefer:

3 posts with 4 holes or 3 posts with 3 holes?
Cyclops AFC with open flow and more positioning options, or cyclops AFC with 3 restrictive holes?

It all depends on what u r looking for. I've always preferred the snubbie because of the AFC. And if you had to rebuild a bunch of them daily, you'd appreciate the 4 holes for a less-fiddly time. But that's just me. IMO flavor quality between the two are almost the same. The difference in flavor is not as pronounced as say, between the Mad Hatter and Mad Hatter mini.

Tobeco clones are very cheep...not much of a risk to buy one of each model and compare for yourself.

Last time I fired at 6w was on 2.2 ohm protank2, vamo mod. Those days are gone hehe

Need to know what device he's using.. Could b one with no step down. Or maybe 6w is still nice to some

no... tarak resistance mana ada heat ??... thats basic of electricity..

my mod max 50 watt.. min 6 watt,.. mech mode on 1.2ohm only 8-10 watt..
at 15 watt the juice taste funny liao,.. 20 watt got burned cotton carbon smell liao...

bro.. your so called "last time" must be at least 1 or 2 years ago...

6w if nice... the only reason is because the users haven't try anything higher... I started with 8w myself... ever since subohm generation, there's no way back to anything below 15watt...15watt also only for those very harsh liquids... most of the time, 20watt is the optimum one...

high wattage form formaldehyde,.. bro

my mod is an ancient X-pro M65,...or maybe it's a cap palang one..

This post has been edited by Special Agent: Dec 14 2015, 05:28 PM

There is one argument which I fully agree. We do know the short term effects are very little but we've yet to determine what long term side effects it would have. It's still in it's early stages to be able to determine what vape would cause to people's health.

I had a friend who gave me a simple formula regarding resistance. Please bear in mind that I'm not responsible for what you'll think about once you read it:

"When you piak piak, if have high resistance won't be syiok right? But if low resistance, no more pain right? Which you think is better".

Please don't condemn me for my friend's simple explanation on resistance

bro.. the higher wattage achievable thanks to low resistance... for example, using 1.2ohm, u need around 4.5v to fire 20watt... but, if u are using 0.5ohm, it's only around 3.5V to achieve the same 20watt... if 20 watt burned out cotton with carbon smell.. those with 30-50 watt meletup already... anyway, I am talking from the perspective of regulated mod... not mech mod...

nice one

bro.. formaldehyde is not something confirm... even if it's confirm, two points... 1st, u shld fire above 5V in order to get that... 5V is equivalent to 40watt on my side... 2ndly, cigaratte has higher (roughly 100x) formaldehyde compares to vaping.. so, is formaldehyde a concern?

Formaldehyde is a known degradation product of propylene glycol that reacts with propylene glycol and glycerol during vaporization to produce hemiacetals. -

See more at: http://blog.mtbakervapor.com/the-truth-beh...h.4ti0zua5.dpuf

In order to achieve the voltage necessary to reach the levels of formaldehyde discovered in this study, you would have to overheat your atomizer, burn your coils, and then vape that repeatedly to be exposed.

See more at: http://blog.mtbakervapor.com/the-truth-beh...h.4ti0zua5.dpuf

This post has been edited by warlove3: Dec 14 2015, 05:42 PM