Welcome Guest ( Log In | Register )

56 Pages « < 38 39 40 41 42 > » Bottom

Outline · [ Standard ] · Linear+

 Skylake/Kaby/Coffee/Comet/Rocket Lake OC V1, Show off your OC here

views
     
TSowikh84
post Mar 2 2019, 09:20 AM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(keyo @ Mar 1 2019, 04:28 PM)
ok tak kalau saya just pakai primeĀ  95 tq
atau ada software lain? tq
*

QUOTE(keyo @ Mar 1 2019, 08:36 PM)
*
Stock clock and no OC? hmm.gif

Other than Prime95, you can also stress with LinX, OCCT, Realbench v2.56, AIDA64 etc. All this is listed in the Post #1.

For testing AVX stability, P95 (with AVX/FMA enabled) Custom Blend 1344K min/1344K max for 3hours+ is sufficient enough.
Small FFT will give you unrealistic load, so avoid using it unless your cooling is able to handle the heat output.

Also, watch out for the VRM temp (read via HWiNFO64 if your mobo has VRM temp sensor) as it will get hot very fast without active cooling facing toward the VRM heatsink.

This post has been edited by owikh84: Mar 2 2019, 09:22 AM
keyo
post Mar 2 2019, 11:07 AM

Casual
***
Junior Member
345 posts

Joined: Jun 2009


QUOTE(owikh84 @ Mar 2 2019, 09:20 AM)
Stock clock and no OC?  hmm.gif

Other than Prime95, you can also stress with LinX, OCCT, Realbench v2.56, AIDA64 etc. All this is listed in the Post #1.

For testing AVX stability, P95 (with AVX/FMA enabled) Custom Blend 1344K min/1344K max for 3hours+ is sufficient enough.
Small FFT will give you unrealistic load, so avoid using it unless your cooling is able to handle the heat output.

Also, watch out for the VRM temp (read via HWiNFO64 if your mobo has VRM temp sensor) as it will get hot very fast without active cooling facing toward the VRM heatsink.
*
oc ram is it can stress test using prime 95
TSowikh84
post Mar 2 2019, 12:15 PM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(keyo @ Mar 2 2019, 11:07 AM)
oc ram is it can stress test using prime 95
*
Yes, if 90%+ RAM capacity is being stressed.
Test will terminate or error will show in certain workers in case of RAM OC failure.
This will take quite some time to see an error.
Best and fast would be RunMemtestPro, which can be downloaded right from Post #1.
However, this software will only stress the RAM alone.
wongtheboy92
post Mar 2 2019, 02:35 PM

Enthusiast
*****
Senior Member
802 posts

Joined: Dec 2008


QUOTE(owikh84 @ Mar 2 2019, 09:20 AM)
Stock clock and no OC?  hmm.gif

Other than Prime95, you can also stress with LinX, OCCT, Realbench v2.56, AIDA64 etc. All this is listed in the Post #1.

For testing AVX stability, P95 (with AVX/FMA enabled) Custom Blend 1344K min/1344K max for 3hours+ is sufficient enough.
Small FFT will give you unrealistic load, so avoid using it unless your cooling is able to handle the heat output.

Also, watch out for the VRM temp (read via HWiNFO64 if your mobo has VRM temp sensor) as it will get hot very fast without active cooling facing toward the VRM heatsink.
*
How to check the VRM temp? Or need to see board, this Asrock board seems can't read the VRM.
TSowikh84
post Mar 2 2019, 08:57 PM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(wongtheboy92 @ Mar 2 2019, 02:35 PM)
How to check the VRM temp? Or need to see board, this Asrock board seems can't read the VRM.
*
QUOTE(owikh84 @ Mar 2 2019, 09:20 AM)
Also, watch out for the VRM temp (read via HWiNFO64 if your mobo has VRM temp sensor) as it will get hot very fast without active cooling facing toward the VRM heatsink.
*

wongtheboy92
post Mar 3 2019, 02:07 PM

Enthusiast
*****
Senior Member
802 posts

Joined: Dec 2008


4.9GHZ @1.23V for RealBench 4hrs
Cinebench R15 @4.9GHZ I got 1600, I got 1637 for 5.0GHZ. Pretty not much of a difference.


Attached thumbnail(s)
Attached Image Attached Image
TSowikh84
post Mar 3 2019, 08:45 PM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(wongtheboy92 @ Mar 3 2019, 02:07 PM)
4.9GHZ @1.23V for RealBench 4hrs
Cinebench R15 @4.9GHZ I got 1600, I got 1637 for 5.0GHZ. Pretty not much of a difference.

1.23v-1.216 = +0.02v vDrop.
This ITX mobo seems not bad in voltage/LLC control with minimal voltage fluctuation between load and idle.

wongtheboy92
post Mar 3 2019, 11:37 PM

Enthusiast
*****
Senior Member
802 posts

Joined: Dec 2008


QUOTE(owikh84 @ Mar 3 2019, 08:45 PM)
1.23v-1.216 = +0.02v vDrop.
This ITX mobo seems not bad in voltage/LLC control with minimal voltage fluctuation between load and idle.
*
I am using the highest LLC level which is level 1 for asrock. lvl 7 for asus right?
TSowikh84
post Mar 4 2019, 12:21 AM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(wongtheboy92 @ Mar 3 2019, 11:37 PM)
I am using the highest LLC level which is level 1 for asrock. lvl 7 for asus right?
*
ASUS Z370 LLC7 max (lowest vDroop is LLC6)
ASUS Z390 LLC8 max (lowest vDroop is LLC8)

wongtheboy92
post Mar 4 2019, 12:56 AM

Enthusiast
*****
Senior Member
802 posts

Joined: Dec 2008


QUOTE(owikh84 @ Mar 4 2019, 12:21 AM)
ASUS Z370 LLC7 max (lowest vDroop is LLC6)
ASUS Z390 LLC8 max (lowest vDroop is LLC8)
*
I think I need watercooling only can try 5.0GHZ probably start at 1.25V. And this is an undelidded chip that's why it runs hot even when voltage is not much. For memory oc, which softwares are recommended?
TSowikh84
post Mar 4 2019, 06:33 AM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(wongtheboy92 @ Mar 4 2019, 12:56 AM)
I think I need watercooling only can try 5.0GHZ probably start at 1.25V. And this is an undelidded chip that's why it runs hot even when voltage is not much. For memory oc, which softwares are recommended?
*

QUOTE(owikh84 @ Mar 2 2019, 12:15 PM)
Best and fast would be RunMemtestPro, which can be downloaded right from Post #1.
*



TSowikh84
post Mar 7 2019, 09:53 PM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



Anyone tried the new Cinebench R20 already? biggrin.gif
Here are my results on two PCs...

9900K @ 5GHz | Maximus XI Gene | 2x8GB DDR4-3200 CL16
user posted image
user posted image

8700K @ 5GHz | Maximus X Formula| 4x8GB DDR4-4266 CL19
user posted image
user posted image

This post has been edited by owikh84: Mar 21 2019, 09:57 PM
wongtheboy92
post Mar 11 2019, 10:05 AM

Enthusiast
*****
Senior Member
802 posts

Joined: Dec 2008


QUOTE(owikh84 @ Mar 7 2019, 09:53 PM)
Anyone tried the new Cinebench R20 already?  biggrin.gif
Here are my results on two PCs...

9900K @ 5GHz | Maximus XI Gene | 2x8GB DDR4-3200 CL16
user posted image

8700K @ 5GHz | Maximus X Formula| 4x8GB DDR4-4266 CL19
user posted image
*
Those scores are good. 9900K is very performing
Diademz
post Mar 14 2019, 07:38 PM

Folding@Malaysia needs you!
Group Icon
VIP
1,246 posts

Joined: Jan 2003

Wa OC sifu owikh84 geng! notworthy.gif This is my 8700k @ 5ghz, GB Z390 Pro with 3200mhz RAM.

user posted image
TSowikh84
post Mar 14 2019, 10:21 PM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(Diademz @ Mar 14 2019, 07:38 PM)
Wa OC sifu owikh84 geng!  notworthy.gif This is my 8700k @ 5ghz, GB Z390 Pro with 3200mhz RAM.
*
Not bad, very close to my score wow!
Keep it up mate biggrin.gif
List updated...
TSowikh84
post Mar 15 2019, 06:59 AM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



New toy in the house, MSI MPG Z390I GAMING EDGE AC.
Gonna take it for a spin with 9900K and some B-die's wub.gif
user posted image

QVL memory up to 4800:
user posted image
Diademz
post Mar 15 2019, 07:24 AM

Folding@Malaysia needs you!
Group Icon
VIP
1,246 posts

Joined: Jan 2003

QUOTE(owikh84 @ Mar 14 2019, 10:21 PM)
Not bad, very close to my score wow!
Keep it up mate  biggrin.gif
List updated...
*
No need to update list! Anonymous will do! smile.gif


QUOTE(owikh84 @ Mar 15 2019, 06:59 AM)
New toy in the house, MSI MPG Z390I GAMING EDGE AC.
Gonna take it for a spin with 9900K and some B-die's wub.gif
user posted image

QVL memory up to 4800:
user posted image
*
Wa ITX. Great for SFF/HTPC use? Not playing with Ryzen? smile.gif
TSowikh84
post Mar 15 2019, 07:57 AM

i7 Clan
Group Icon
Elite
8,705 posts

Joined: Nov 2007
From: Butterworth, PG / Machang, Kelantan



QUOTE(Diademz @ Mar 15 2019, 07:24 AM)
No need to update list! Anonymous will do! smile.gif
Wa ITX. Great for SFF/HTPC use? Not playing with Ryzen? smile.gif
*
Just for record fun bro haha.
Sold off my 2700X + C7HW few months ago so that I could afford to buy the 9900K + M11G.
However, just recently I bought the 2600X while awaiting for the AM4 ITX board to arrive from Taobao, the ROG Strix B450i. Will update in the Ryzen OC thread soon.
wongtheboy92
post Mar 16 2019, 12:21 PM

Enthusiast
*****
Senior Member
802 posts

Joined: Dec 2008


4.9GHZ @ Fixed VCore 1.25V LLC 2
5.0GHZ @ Fixed VCore 1.28V LLC 2 (not fully stable, but able to run cinebench at least)


Attached thumbnail(s)
Attached Image Attached Image
Silverfire
post Mar 17 2019, 02:56 AM

Cruxiaer
*******
Senior Member
4,946 posts

Joined: Nov 2007



Just achieved Rank 33 for 3DMark FSE biggrin.gif

https://www.3dmark.com/fs/18743832

56 Pages « < 38 39 40 41 42 > » Top
 

Change to:
| Lo-Fi Version
0.0159sec    0.54    6 queries    GZIP Disabled
Time is now: 29th March 2024 - 11:53 PM