I'm using Abit KN8 and Athlon64 3200+ (Venice E3), I set the proc at 240FSB, HTT at 3x, CPU voltage 1.4v, and RAM to 133MHz divider. The mobo malfunction, and it never boot anymore, any IDE connected to the mobo didn't receive power unless I unplugged from the mobo. I tried clearing CMOS, but nothing happened. I think the mobo just gets fried up, Abit motherboard is never good at OC which dissapoints me much.....

saying that abit boards dont clock well, its like saying you were born with a peanut in your head.

it depends how you clock them. i've moved from abit to msi and i hate msi even more. its crap!

what is the amd64 3000+ code name at the market now?

yesterday i get my venice 3000 up to 2.34 ghz, but it can only happen if i set my ram to 166mhz eventhough the RAM is DDR 400..if i set to 200mhz even i set the frequency to 239 sure RAID detected oredi...before i update the BIOS this problem didn't exist....????

my ram now only able to do 210 stable in all test (512 KVR double side, wanna change it asap)

if i oc to 220 x 9 , and it can boot up but it failer Prime95 then should i up Vcore first or vdimm??

This post has been edited by tachlio: May 18 2006, 09:58 PM

Erm...wanna ask somethin guys, b4 OC ppl always say go for burn-in 1st, what accually burn-in means n what it helps in the OC part???

Yesterday am magical thing happened, just discovered that the KN8 come to life again, my friend asked me to check the mobo again in case it is my RAM's fault. Now I can reach 2.4GHz with 1:1 divider using KVR400, guess I was wrong after all, it is my RAM's fault........

One thing I'm not sure is the correct timing for the memory when operating at 1:1 divider? Can anyone help me?

[attachmentid=110641]

[attachmentid=110642]

This post has been edited by revived_irfan: May 28 2006, 08:19 PM

my AMD 64 3000+ Venice clock to 2.25, do I need to change the HSF? Currently using default HSF from the box

this is what i get with my opteron, which one to go for?

280x9 with 100Mhz divider or 260x9 with 166Mhz divider?

i think so..

what ram are you using? if using ram with good chipset why dont try 300mhz with 1:1 divider

Just cheap Kingston valueRAM, cant go above 240HTT with 200Mhz divider

I having a weird problem with my Opteron 144 OC. It can do 275HTT 3XLDT default Vcore dual SP2004 stable for over 5 hours. RAM with divider to make it below 200Mhz FSB. Latency 3-4-4-8(Infineon BE5 default 2-3-2-5 PQI Turbo Memory 2GB dual channel kit) . The weird thing is once I use 280HTT it won't even POST to bios screen. No display at all. Even pump up 5% and 10% Vcore and PCIE set to 8up 8down also cannot post. Proc temp always below 50. Stepping CAB2E 0540. Anybody faced this no display prob when OC before?

This is My...haih PSU is nop stable again.will get 460W FMA try later.

Mobo:T-force S939
Ram:Value select PQI 512MB DDR=Single channel
E6 A64 3000+
stock cooling HSF
150 Divider now...


the ram limit and PSU is unstable.shit.....should be better after psu and dual channel on with UCCC chip

This post has been edited by Vtec(Rock): Jun 5 2006, 11:28 AM


Attached thumbnail(s)

this is what i do 2day, oc my 3000+ Venice (S939) to 2.7GHz

Mobo: Asus A8N-E
HTT: 301
Multiplier: x9
Voltage: 1.525v
Hyper Transport: x2

CPUZ: http://valid.x86-secret.com/show_oc.php?id=101480



This post has been edited by gmail: Jun 22 2006, 09:13 PM

hey guys.... can tell me wheter dis is a good oc stepping...
ADA3000DAA4BW
NBBWE 0618FAB
X100347E60173
... dis one says made in china on the proc...i thoght all made in malaysia... or my eyes were decieving me..must check again.... i figured this proc is week 18 year 06..so it was made sometime in march....

hey guys.... can tell me wheter dis is a good oc stepping...
ADA3000DAA4BW
NBBWE 0618FAB
X100347E60173
... dis one says made in china on the proc...i thoght all made in malaysia... or my eyes were decieving me..must check again.... i figured this proc is week 18 year 06..so it was made sometime in march....

nothing can we tell unless u can give us that proc and i test it for u

the newer batch of A64 939 3000+ are made in china, while semprons are made in china since late last year. OC-ability seems on par with those made in malaysia

is it as good as the e3?