Has anyone tried fixing their logitech mouse for double click issue? my mouse still under warranty by I can't seem to reach Logitech malaysia

Just desolder the trash stock switches and change them to some Kailh GM2, GM8 or Huano white dots. No more double clicking, much better feel and response.

This post has been edited by SSJBen: Sep 15 2021, 03:40 PM

i have DA chroma and have the issue... out of warranty... sadly... idk how to desolder it.

Then learn. If you can tie your shoe lace, you can learn how to solder. Shouldn't be an excuse.

1) Unscrew shell
2) Unscrew PCB
3) Heat up mouse pin on PCB
4) Add a little bit of solder
5) Immediately desolder with a solder pump
6) Repeat the same for each pin
7) Wiggle the switches out from PCB
8) Put in new switches on PCB, heat up the pins, put solder on
9) Repeat for opposite side (LMB or RMB)
10 Screw everything back, enjoy

Literally 10 minutes job. Even for a beginner, shouldn't take you more than 20 minutes.

This post has been edited by SSJBen: Sep 17 2021, 03:23 PM

u miss out 1 step...applies in most cases
replacement mouse feets

Ah yes you're right. That step is so automatic that I don't even think about it anymore.

what mousepads are you guys using with superlight..

after changing from g703.. found it a bit weird..
and hmm not even sure the onboard dpi profile is working correctly with the onboard mem manager software..
it works fine with ghub but hmmm

seems like hardsurface i have no issue and cheapo mousepad seems like screwed up.

so thinking should i just get the fnatic dash, artisan or hmm some hard surface.. trying to transition to soft mousepads also atm.

i dont have superlight but using G304 which is somewhat very close in terms of sensor. no issues with my 10 years old icemat... although now switched to Mr.DIY mousepad that seems pretty decent lol.

Using:

1) Razer Gigantus V2 L
2) Artisan Zero L (Mid thickness)

The Gigantus for general usage, the Zero when I game. Mouse is OG GPW but modded switches to Huano white dots.

not sure g304 but definately superlight very sensitive to mousepads compared to my g703

Might be the weight... heavier mouse can feel more stable. Lighter mouse is more slippery... especially if you play high sensitivity on a light mouse. You might wanna consider "control" type surface.

its not that..
its the feeling of the dpi

the superlight is inconsistent on x/y

This post has been edited by cstkl1: Sep 21 2021, 08:22 PM

hmmm better pinjam other superlight and see.. sounds like sensor issue dont think it's the behavior of one of the best mouse in the market.

its fine on better mousepad. once i use my logitech hard mats etc sitting around

just suprised ...it is so sensitive to cheapo large mats

atm.. looking at fnatic dash more for the size of XD ...

This post has been edited by cstkl1: Sep 21 2021, 08:36 PM

hi I need some recommendation/feedback on getting a second mouse.
Im using logitech master mx3 and looking for some similar alternative that have marco capability..

googled around and found g604, but the review is not as good..not sure what the reason.. anyone using g604 can give some feedback?

usage:
1) +- 2hours per day when i need to performance some task that marco will be really helpful
2) free scrolling.. MUST
3) wireless if possible
4) as cheap as possible

u can basically short list down the models that meet #2&3.
Not much models hv hyperscroll

from there pick #4

yup that g604 come into pic.. i search g604 in this thread.. and no discussion.. haha
tot can ask for some other recommendation

Sounds like a LOD issue. May want to check for sensor rattle.

its also damn weird with cheapo rm 19 mousepad
plug in ghub set my dpi 1050
its fine.
save to onboard profile
uninstall ghub
not fine
checked via their onboard mem portable app
its correct

plug in back my g703 all good.
cheapo mousepad fine

use back old hardpad that came with powerplay superlight is fine..

This post has been edited by cstkl1: Sep 22 2021, 07:11 PM

AFAIK Ghub has to be kept installed for arbitrary DPI values to be set - otherwise it'll always be rounded to the closest default values (400, 800, 1600, 3200). Yes, stupid I know. I'm unsure if they've improved on this area or not, because I'm still using the the old LGS which is a rock solid piece of software.