wat u tryin' to mention here??
dya mean all HZseries no need to put manually timming??

wat i mean by 3-5-5-10 was the label on the heatspreader of this HZseries. r u suggesting to use the default speed??

This post has been edited by gengstapo: May 29 2006, 10:51 PM

This is the SPD tab i was talking about. It shows 3-5-5-10 instead of 3-4-4-8 is because when non-overclocker set everything to AUTO in bios, it will not detact as 3-3-3-6 and that might cause some problems for non overclockers. Go through my post a few times if you still don't understand what I'm trying to say to you.

Can you take a shot of your heatspreader? I've never seen a 3-5-5-10 HZ on heatspreader before.

ouchh.. get it ady. well, just look at the heatspreader, its wrote 3-4-4-8. mebe wat i saw b4 was the cpu-z timming.

besides the setting, vdimm is very important to this ram as well.. believe me, u wont need more than 2.7vdimm for this ram.

currently i'm running my pc @ 270 1:1 2.65vdimm.. well i still think 2.65 is a bit high for this ram..

sure wan leh?? last nite kenot pass PI Calc. 32MB at 385HTT wif 2.6vdimm. then tried raise to 2.7vdimm then onli can pass(run twice free problem). mebe my HTT lil hihger than urs

this nite will try tweakin' again to get the 300HTT

385htt is for the cpu rite? ram u use divider? coz if u mean 385htt for the ram as well (1:1), then ur ram already running at 770mhz!

i think cpu htt is not the issue here.. the most important thing is the ram frequency.. thats why when we need to oc the cpu alone we need to use divider so the ram wont oc too much.. if i run my cpu at 350htt x 10multiplier, but using divider 150.. my ram will only run at its rated speed 250mhz.. and i think the most important here is the ram speed..

correct me if i'm wrong. i also started to confuse

If you can get the HZ to run at 280-290 1:1, you can consider yourself lucky to have a great module. Mine can do 280 1:1 @ 2.5V. 2.6 and above no go.

aiyakk.. sorry leh, typo. i mean 285HTT(divider 5:6) onli, highest prime able was 290HTT(divider 5:6) & both were at 2.7vdimm. i cant tweak nicely, dunno wat need to be tweak ady since whenever the HTT pass the 285, i need to raise the processor vcore ady. lastnite i can get 3Ghz but temp kinda high, so now running at 285HTT onli

Oh no, after adjust the MAL and RP in the bios then the Windows failed to boot. how come?

probably too tight
what did u put..??

as for me, i did trial n error, took me 3 friggin day to find a stable settings
so, be patient when tweaking..

p/s: did u know what each of those timings are for?



This post has been edited by e-jump: May 31 2006, 08:33 PM

i also did to try and reset the jumper... Cant find any value that allows me to boot properly... sigh! thanks that picture.. i will follow it...

This post has been edited by swgiant: May 31 2006, 09:45 PM

The 3-5-5-10 is normal for new batch of HZ if i'm not wrong.
bmbk who bought the same ram from me got tons of errors with 1 stick in memtest suddently after few days of tweaking.RMA?Replacement?

i dont facing any prob wif king' g.skill HZ 2gb kit..
after slot em', i just boot BIOS to the default max setup. i just change lil' setting such timming, put divider, decrease the ldt multi & some other setup for the RAMs. dunno wat wrong, my opty temp was high. hence, i just run my rig at 285htt x10, divider 5:6 & vcore 1.4v while vdimm at 2.6 onli. mebe need to change the cooler, currently using XP-90.

That's it.All the buyers are doing good with their HZ but bmbk got some problem with 1 stick after few days and he assume it as DOA,asking for refund someore. Hope his HZ don't have any burn mark.

gengstapo@
Your vcore still low and xp-90 is a good cooler too,how come your temp high.What is your temp?

@gengstapo why runs your ram at DDR 475? why not higher than DDR 500?

anyway, how to force my mobo to run 1T? sometimes i saw it runs 1T but soemtimes 2T... any idea?

oh snap..
edited

This post has been edited by e-jump: Jun 2 2006, 02:15 PM

well, dunno what wrong. even at 1.4v, my opty kinda hot & can reach 58c full load. mebe times to change the XP-90


well, i can run DDR500@ 300HTT, but my opty temp very high. wait after i change my cooler, u will c it running at 300HTT@ DDR500

gengstapo, u r talking about both ocing proc and ram...no wonder even irenic got headache...swgiant is looking for help to get the max oc for his ram la bro - same as i am...but ur talking about getting the best out of ur proc and mem --> 300HTT@DDR500... kasi fenin orang la...
anyway...what is the best u can get from ur mem?and btw, whatabout the bios version...any good suggestion on which bios to use...for dfi nf4 lp...

did u set the Command Rate to Auto???btw, what mobo do u have???

This post has been edited by remysix: Jun 2 2006, 10:30 PM