There's only one shield connector. If you want to use two shields for the arms, you'll have to use the gatling guns.

Thanks Man.. Think may repaint it since I have 1 more tt hongli FA..

iya nih gan di indo kitnya mahal-mahal . Ikut PO hlj aja harus list price jarang yang ngasi sale price, gk ada malah jadi jatohnya mahaaaalll, sory curcol! OK BTT, does any one have tutorial for painting sinanju head base? just receive my daban sinanju yesterday. Daban itself has raising the bar in the world of bootleg gunplas they made a nice copy from pandai except the polycaps are still lill bit sucks, i found many inconsistency with the polycaps. sometimes its good, can hold many poses and doing their job, but sometimes its sucks it would even hold the parts into the balljoint. i dont know its just me or anyone have the same problem. Ps my daban sinanju have warped rifle it bends to the left any tips for straigthen them up?

Polycaps can be tighten by apply a thin layer of cement over it, wait until it dry only install back unless u want get fix post.
Rifle can be fix by heating up with hot water/hair dryer, heat until the plastic soft then bend it back to original form.
Tutorial for sinanju head stand? Not sure why you want, you just need to paint it back to original colour or your custom colour. Emblem can be paint by marker(Artline 990XF recommended by many modeler here, and I bought it today effect was nice), reverse wash technique, hell of masking which is handbrush... Reverse wash technique was easiest in my opinion but I don't have the proper paint and airbrush so I just use marker pen.

This post has been edited by TheGreatBahamut: Aug 4 2013, 09:46 PM

did you mean just rub it inside the polycaps then wait till it dry? ok i'll try it very soon will report it a bit later since i was a noob i'm afraid i'm gonna break the rifle instead of straightem up . Yess master i mean tutorials for painting the emblem or isignia not the hole process, is my bad . The emblem are prety hard to paint it is realy lack of spaces for masking em up. maybe i'll go with the reverse wash technique, google it pronto. thank you

Haha u can apply inside the polycaps or the joint/male peg that going to fit into the polycaps.
For painting, use very fine tip marker can also skip masking but do make sure that the tip wasn't too wet which the paint will overflow, reverse wash still the best just need lacquer base gold under enamel black and then wipe off the enamel black on the emblem with enamel thinner or zippo lighter fluid.

This post has been edited by TheGreatBahamut: Aug 4 2013, 11:05 PM

slow slow work...without touch up yet




This post has been edited by verdangilte: Aug 4 2013, 11:29 PM

looks like the MG strike to me

MG launcher and sword strike?

lol...just a noob strike...still got many place not yet touch up...i guess time to get some pen ??

for MG Strike, a scriber would work wonders too

i not understand about bro

panel line scriber... basically u use the tool to carve your own panel lines, giving the kit more separation and 'detail'

can ask more about it from sifu mf_yamato

kasi chan la people excited.. hahah

lol...for a newbie as me quite challenge...
but i now more on find about the marker to touch up...
beside...step for top coat is...after we sanding give the top coat only touch up or sanding > touch up > top coat ??

i now thinking get flat colour...

can share what kind of scriber you are using and where to get?

i want to start but duno where to get a scriber ..

wuwuw me no sifu la huhuhu

i use custom scriber as i'm a cheapskate..
i inserted a needle into a mechanical pencil (0.5) then, taddaaaa a scriber..
but there also a specific scriber for modelling, I bought U-star brand iinm huhuhu can't remember arround rm25 with template i think....


belanja u a pic, both of my scriber and scribed part huhuhu

is it hard to scribe the models? i was thinking to add some details to my gundam but, don't have any confident at all

not that hard actually, just draw the line, stick dymo tape close to the line, and scribe it,
the major problem for me is to imagine the line on the parts, too much details will ruin the kit, ant you hand maybe??

hahah .. thx bro .. basically your scriber is just a pin like thingy?

i try to use the back of a craft knife but the line doesn't come out nice .. a little wavy and uneven ..

and where to buy the U-star scriber? can share?