Once Upon A Time At Antonio's Lair

Ok fellow friends, antonio is back to bring the fun and excitment in the scene. As u all know that not much Intel people dare to bring up their overclocking 'ciput' since right now all the abang AMD has tapau us all.

But no sweat...8k in Sandra mem bench doesnt mean anything if your still runing under 4G's....hahahah...ya thats rite...4G brother...well i'm also short of that amount...so lets gather and open a 4Gigahertz shall we??

AMD

-So this is first run...3.8 teruss...no kasi chance wan...



-This were a lil bit brave...bump up voltage a bit and start craking...



-This is the 1MB run of the seriously (saat-saat getir) 4 non stop Dunhills....



-Not enough stability in my book...so i ran an instance of 32MB to see what happends...Temp being beeping like hell...



well...as for CPU-z validation can be found here----> http://valid.x86-secret.com/show_oc?id=85819 or http://valid.x86-secret.com/show_oc?id=85818

:Notice:
-no 3D testing...(not a fan of 3D anyway)
-games : played Godfather EA & CM2006 12 hours...No problem...
-Temps max were 63c
-bump voltages 1.45v
-who say's putting two Presscott core in a single chip is no good??

This post has been edited by antonio_zth: Apr 13 2006, 06:19 PM

break 4Ghz bro..
eager to see them..
no chance to break mine b4 coz psu bottlenecking..

I cant...board do not allow.....

what cooling system u use?

This post has been edited by kulus: Apr 11 2006, 11:54 AM

Standard HSF running backup with Delta 120mm

What's the idle temp and full load temp for the highest clocks archieved?

This post has been edited by Hyde`fK: Apr 11 2006, 12:59 PM

now that's where your money went

any intel user can reach 4Ghz?

mine can.... but prescott la

It seems tone has a Cedar Mill doing 4.65ghz

Wow..that 805 is really high overclockable. But..i notice your ram running at 190mhz = DDR380? You underclock it too far for DDR2 . Try with tighter timing and higher clock for ram. Your superPI is very slow for a 3.9ghz . Perhaps due to ur Slow DDR2 runing at DDR380
No offence here.

This post has been edited by Cyclone87: Apr 11 2006, 05:29 PM

idle around 36-39c
max load temp would be around 63-67c...


hihihih...no lar...


erm..a few guys here...view the intel thread to know more....


no lar...maybe it is actually downclock a lot...

the problem with DDR2 and my mobo is that it cant run at 1:1 which is supposed to be DDR 133 while FSB at 133 aLSO....if i set the ram at that speed...my overclocking would be around 3.0gig only....

waitttttttt
you running it at 1:1 O.o got 1:1.3 or not?

I would like to command you to do the prime TEST NOW!!!!!!!!!!

Just to provide a better picture of system stability, just whack it for 2 hours is good enough for all of us. I hate SUPERPI because it's quite easy to pass, most of the time extensive or critical applications like installing kernel module for linux would hang provided the system is not stable when priming. It does happen to me couple of times before and I completely hosed my system.

This post has been edited by PCcrazy: Apr 12 2006, 06:52 AM

im running 1/4


Prime...later boss coz rite now still need to rectify cooling problem...thermal reach up 67 last nite and thermal protection only at 65c...arghhhhh

2.6Ghz clocked to 3.9GHz... woow... 1.3GHz more gained.

DDR2 Multipier got 4x...
so is 190*4 = DDR2 760...

u are funny....

haha...

juz kidding.....

walao wanno throw my sempron liao...how much u bought the 805?if not wrong it is quite affordable i suppose?
wats the mobo used?
damn nice, thumb up for u bro!

not what i'm targeting actually....i'm in need of 4 and untill then...will not stop pumping vcore...yeahhh

bang...bila nak memain Intel nie???dah ada belasah jerk la...


Around RM500...Mobo like in my siggy....for sale now....

Sempron oso good in overclock...but the feel of high megahertz takder...thats why less thrilling....but benchmarks scores all the same only....

oit hentam 805 tu trus la..

celeron boleh join bro antonio?..

This post has been edited by newbieockids: Apr 12 2006, 04:07 PM

abg antonio_zth, buat ler 4.0GHz Opty
that time u'll b the benchie king in LYN ady, hahaha.

ish..Opty 4GHz....terpaksa pasang ekzos kat PC nanti....
bang antonio....good luck! malaysia boleh!

boley...we LYN overclockers maaaa....if achieve to deliver, its not only a personal but the whole LYN image....

OPty???iskk...aku tak kaya ler...need $$$ also to buy opty.....

Ekzos maybe not....LN2 is a must....

yo anton,

let form a 4ghz club:
Paging for all Intel user with 4Ghz.
Pls summit ur results!!

here's mine.
P4 631 3Ghz@4.7Ghz.
Abit IL8 Mobo
2 X 512MB Micron DDR667
eVga 6800 Ultra
Enermax Liberty 500W
Chapalang Water Cooling (china made)



anton: Push somemore la...!! abit only..try cooling ur mobo mosfet..put a 8cm fan ontop of the mosfet.

This post has been edited by tone: Apr 13 2006, 12:23 AM

Great overclocking, it has been a long time since the northwood era. I say bring it on the stuff tone and antonio.

Honestly I'm lacking knowledge of Intel processor and motherboard since the introduction of AMD64 939. Oh not to mention about DDR2, I have had many friends asking which brand of DDR2 to go with Intel and I simply have no idea. I guess too much on one sided platform makes me ignorant about the rest of the platform.

not that much....all kinda same actually....but a limited option compare to DFI genie bios....

ddr2 is very ocable..
ddr2 533 confirm can reach 667 speed with 4/5-5-5-15..
this is done with pqi ddr2 533(DDR 680 @ 4-5-5-15)..

it should be go higher with CL5.. ive tested KVR ddr2 533 stick and it is very easy to reach DDR 667 as well..

@tone
what is the timing for ur DDR667 @ stock?...

tempting la like that....

yup but the timing..
waiting for tone to respone..
if it is the same, no use to buy ddr2 667..

wahaha..4Ghz club..sound nice..

May i join?

Once upon a time benching with eKok and ah_chak's Celeron D coupled with AI7....
4.11GHz stock heatsink ain't too shabby

d figure fever is here again... keep it up all...

where's kcnyc...

long-long time ago

Guys..post up some superPI. I m intrested with the result. 1M or 32M is std.

of coz cannot lawan otai2 amd lar..

max voltage for ddr2? 2.1? 2.3?
anybody know?

i still remember that b4 a64 939, prescott was d king of pi... scorin big bcoz of their 1MB l2 cache...

2.1 should be gud enough..
unless u going for ~1000MHz above..

find ur micron max performance rite now..
juz wanna know izzit worth to buy ddr2 667..
oc'ed 533's-->667 use the same timing like urs..

This post has been edited by newbieockids: Apr 14 2006, 12:30 AM

with 2.1volts..DDR790
316mhz fsb..4:5 ratio..pushing mobo to the max liaoz..945P chipset..

This post has been edited by tone: Apr 14 2006, 12:40 AM

haha its the time for 975..
selling board again?..

neh! im gonna wait for conroe..no point changing now..hehe..

conroe will work with 975..
no point selling 945 when conroe is out..
just my humble opinion..

This post has been edited by newbieockids: Apr 14 2006, 01:19 AM

me oso achived 4Ghz b4...hehe...juz to report in la...

max vcore i'm applying is 1.475v which is quite low to prime at 3.5g....i need to watercooled and maybe dust of my pelting kit just to cool down the 67c mark on prime peak temp constant at maybe 2 minutes a drift...

antonio, it's better you go pure water and sort it out with a good waterblock in hand. Amok dah prove dah pakai storm dia actually

ur presscott sejuk meh? pakai cooler apa?

Bukan Prescott aku. Amok's using WC'ing setup of Dangerden Heatercore, Laing D5 and Swiftech Storm G4

here's my temp:
china made watercooling.

P4 631 3Ghz@4.5Ghz 65nm

and ur procs/mem running at?..
nice temp neway..

edited:
ooppss i view ur post quite fast..
lol nice temp..

This post has been edited by newbieockids: Apr 16 2006, 11:46 PM

Cedar mill runs very cool...

is there any way to achieve 4GHz on stock cooling?

i pushed it up all the way to 300FSB on my 2.4Ghz but it wouldn't boot at all? i'm on OCZ EL Platinum TCCD, so i guess RAM is not an issue. what is the reason?

im sorry but what kind of 2.4 that u use?...

u should be in 5GHz club not here..
neway any chance breaking 5Ghz bro?..

p4 2.4 C

300*12 i guess that should be too much for ur procs..
maybe u need extra VCore and some decent heatsink that better than stock..
what is the timing that u put for ur ram?..

i put 1.55vcore and my ram timing is 2.5-3-3-7 on 2.8vdimm (max). divider 1:1. maximum FSB i can go is about 360 which i'm able to hit 3.2GHz.

r u sure ur fsb at 360?..
360*12 that mean ur procs is running at 4.32GHz rit now bro..
beside 360@2.5-3-3-7@2.8 with tccd is a new world record perhaps..

You want your 2.4C to hit 4ghz?
On stock cooling summore....
I doubt that'll be possible for the best 2.4c chip in the world

i am sorry. typo mistake. it should be 260FSB

My 2.8E is able to reach 3.78@1.55v at best effort, still using stock cooling.. I wonder changing to Ninja will help..

hehehh....certainly it is...well while i was busy peltier'ing...i already prepared my upgraded water cool kit from big water to 'huge water'...Pumps + hoses + and fittings including white tape is already purchased...but the problem is time.. not many of em nowadays....

juz 2 more fsb to get 4ghz on default vcore ..

Yo . Bro Antonio , r u using gigabyte GA-8I945P-G ????? and mind to what ram u using. ??????

AGRHHHHHHHHHHHHH...... i had 805 as well OC on MSI 945P NEO cant EVEN POST on FSB > 143 !!

Intel 805 + Kingston 512MB DDR533 (Samsung chip) + MSI 945P NEO-F (ms7176)

Seen like i got the problem same as b4 which i got my NF4-Neo4 plat.!! Cant POST on >215Mhz No matter how i tweak / changing version of bios !! Give up after 2 month

den change Board to DFI lanparty the same ram + cpu, easilly boot up
>280 , prime stable @ 250mhz 1:1 now.



WTF MSI doing . !!!!!!!!!!!!!!!!!



Any Comment for me ?

I faced the same problem when i was first firing up the system. I reckon there is something helding back the 945 Chipset which failing to overclock with 1:1 FSB/MEM Mhz...Only when i put on dividers then only the chip fly high....Eventhou i achieve it to get around 3.9+Ghz i cant push FSB in windows nor bios to get it up to 4G's....

i sent an email to Gigabyte about the matter and you know what the replied me with?



aiyakk...not the kinda response i would hope but well...who can blame em....

My rams are normal DDR533 KVR 512x2....

lol since like this is thier " STANDARD " answer..... aiks this stupid msi board doesnt have fsb/mem divider...... even i set to 133mhz fsb, i also cant even adjust 1 mhz at windows. press " ok" means halt !

haiz. really wondering wth msi doing.... bios also not available to update. !!

Luckily my Gigabyte has PCI/PCIE lock....kudos Gigabyte...

I was hoping to get those DFI based intel boards but just not untill the introduced a later chipset...

try to change ur pcie frequency
as long as it is below 125mhz
i saw a review b4
when they stuck at certain level
they did tried that n found out it can be used to pump up ur cpu more...

wahh...100 to 125 isnt that alot???

mebe can create a name list for those can get 4Ghz?

i dont think its pcie frequency limited the oc result.


i visited the msi forum and found out someone tat says its becos of the 945p chipset limited the oc, the chipset limited the oc not more than 10% from stock clock, only asus and gigabyte has "cracked" the limitation of chipset thur bios.

dunno its real or not.

anyhow i still trying to push higher clock speed.


the weired thing IS even i set the fsb to 133 at bios . when i adjust +1 mhz and become 134MHZ at core centre and apply its STILL HALT.

any msi 945P user here mind share.

can u give the direct link to ur mobo @ MSI website plz?...

This post has been edited by newbieockids: May 2 2006, 02:27 PM

p5wd2

i maybe need to change mobo already....any suggestions???

"The best overclocking mobo for Intel based on 975"

can i post up the score using 3.2e?

be my guest

that mobo will cost at least 1k...
make sure u did explore some of their review 1st bro..
obviously that is the best mobo available out there beside Abit AW8D..
both of them just using 4pin ATX 12V.. if u plan to play with "dwi teras" procs, make sure ur psu have at least dual 12V rails(not a prob for u rite?)..
one more thing normally fanless will not promise the best temp although with heatpipe design.. i guess u need to prepare sumthing for that..

This post has been edited by newbieockids: May 3 2006, 08:19 AM

1K??<--maybe got
'dwi teras'<---got aledi
4 pin ATX12v???<---what the fuk is that?
dual rails??<---I got a PSU with 4 rails...
heatpipe temps not good<----now thats is the thrill all about

this board use 8pin while that board use 4pin.. thats the fuk is it...

This post has been edited by newbieockids: May 3 2006, 12:11 PM

sure

http://www.msi.com.tw/program/products/mai...ail.php?UID=672

what use of the 4 extra pin?
more power to cpu?

Nice OC

4Ghz Intel805 Yet?

who me???not yet...still short of couple more mhz...mobo's holding me back...gosh darn..

With power consumption over 200watts, wat kinda PSU are u using? Water cooling yet?

wah its been long since i last entered lowyat.net forum...

skunk people already want to show off intel 4ghz plak...

thiz wat i've been waiting for all thiz time...

eh guyz....can i join



mine...very² old school d, about few months old (some of u maybe familiar with thiz score!!)

it's a 2.4A presscot with stepping SL88F revision E....manage to clocked it to 4.3GHz from 2.4GHz (default) a 1.9GHz increased ....cooling with tt bigwater, wat u see is the idle temp (42'c) & if im not mistaken the load temp is around (54'c - 55'c)!!mobo is msi 865pe neo2 platinium edition, now the mobo "kong" d.... !!



some of the setup ::

psu :: aerocool turbine 550watt dual rail
ram :: Kingston hyperX 256x2
gc :: galaxy 6800NU
hdd :: wd 80gb (sata)
optical :: benq 1620pro

This post has been edited by amd_scooterist: May 13 2006, 01:32 PM

walla eh..long time dun see...4.3Ghz .. same set up like mine..mah sifuuuuuu..lol...

http://www.tomshardware.com/2006/05/10/dual_41_ghz_cores/

thanx for the link..
damn 1.6V to break 4Ghz for the 805..
obviously heatsink not gud enough man!..

This post has been edited by newbieockids: May 18 2006, 09:58 PM

One Q's.....


it is supposed to show 400,300 or 200 Mhz....





i'm confused here...am i overstressing my rams?

This post has been edited by antonio_zth: May 20 2006, 03:09 AM

yap im having this Question as well. very confuse ,

For ddr2 ram. 200mhz = 400ddr2 rating. 300mhz = 600ddr2 rating. So 266mhz = 533ddr2 rating.

so mine is DDr600 lar rite now.... owh..and it is stable lor...regarding the rams are only KVR 512 ddr2...

i heard that ddr2 533 nowadays very ocable
normally oc to 667 shd not be a big problem...