you can use SF9812DSL since you located at outstation... bcos it have lower replacement cost compare to SF9512DSL and easier to courier back to Muar, Johor due to the small size small tel module for restoration...

if u prefer multi socket version, u can use SF9512DSL MS2+3 or IT Pack...

both of the suggested models only valid for 1 PC complete set with 1 modem only... if u have PC to PC networking via router (connected with many PC via LAN) and have telephone nearby ur PC set, u need additional / other models for better protection...

u can call up 03-77268680 or 06-9517680
for cost efficient, u can email callabkl@callab.com.my / callab@callab.com.my as cal-lab check email frequently...

as i know the total damage is Rm15 (for restoration) + Rm5+ (courier from you to HQ)... but u need to bank in RM15 to cal-lab bank account and provide proof of payment along with faulty unit or email the proof of payment...

if you dont have PC to PC networking / have other networked PCs into router and your router serving your PC only, u can use combination of MDSC0039 + SP9201DAF

1. cal-lab dont have the protection for data COM port
2. only up to 100mbps, cal-lab no support for gigabit at the moments

u have to change whole unit if IT Pack and SF9512 series...
if u want the model which can change the module only, only SF9812 have the replacement module for telephone...

---

Added on December 11, 2010, 8:57 pm
3 unit for RJ45 lan protection?


cal-lab dont have sell timer... only have the light sensor type... if sensor detected the darkness, it will switch on your lamp

This post has been edited by gkl83: Dec 11 2010, 08:57 PM

no required to bring other stuffs such cal-lab box, warranty card, receipt, etc... just only bring ur damaged physical cal-lab unit will be fine...

anyway, recommended to call in into cal-lab show room 03-77268680 for appointment and ask for the availability of the replacement unit which to replace your damaged unit on the spot without spending another trip to get the replacement...

if u using Unifi for your computer setup, hence only 1 PC connected and no TV concerned...
u can protect power source will sufficient...


you can use STV9511 for power and aerial antenna protection...
if u have telephone nearby ur TV setup then u may need other models...

u can use multisocket for extra gang, but it only limited of ur TV, amp, DVD equipments only... excessive power extension no recommended as concerned that may effect the protection efficiency...


PMed

either is bad grounding of your equipments or your multi socket or poor earthing provided by TNB

if your equipments with bad grounding, nothing much can do...
as good equipments usually wont leak any currents out from the casing...

are you using fax machine or dial up modem? if yes, recommended to use SF9512ARD for power & tel protection as concerned that surge may come from power source too...

Setup 1
PC used with ADSL modem and telephone & splitter located beside both PC equipments, u can use the combination of MDSC0039 + SP9201DAF... SP9201DAF will used to replace ur ordinary ADSL splitter filter...

Setup 2
PC + 4 unit fax modem, you can use SF9512ARD + 3 unit SP9201ARD. about your statement "1 modem connected to the splitter", you means this tel cable come from Setup 1's tel cable?

anyway, is it ALL of the equipments as above located in the same room?

here as proposed...

if 1 PC + 1 USB ADSL Modem + 4 USB Fax Modem
since all of your modem powered up via USB, no necessary for MDSC0039...
unless u means your ADSL modem wasnt the USB type, but connected via lan cable instead...


This post has been edited by gkl83: Jan 12 2011, 01:43 PM

1. ur ADSL splitter filter and telephone placed near to ur PC?
2. have any PC to PC networking via same router? (more than few PC inter-connected to modem/router)


what is your equipment list and what is total power consumption? only 2 desktop + 1 modem router concerned? bcos cal-lab have 1000w & 2000w version depend on your load... hence is ur ADSL splitter filter and telephone placed near to ur PC?

so recommended to use the combination of MDSC0039 + SP9201DAF...
if u prefer the multisocket version, u can consider on SLMS2+3 or twin power pack...

if both of PC and modem router located at the same table/area... then lan cable protection no concerned...

as overall, 2 PC, modem router & telephone located at the same table/area, then u can use the combination of MDSC0039 or SLMS2+3 or Twin Power Pack + SP9201DAF

if ur TV no connected any aerial antenna, u can use MDSC0039FC for power and astro protection


u can use SFTv9622FC for power, astro and aerial antenna protetcion...
as long as ur total power comsuption no more than 1000w then should be fine...

you can use Twin Power Pack as it have 4*3pin and 6*2pin power socket...
for telephone protection u can used SP9201 series and the version depending on ur tel source usage such as dial up, broadband, etc...

Whether or not protection will be effective depends on whether a safe-island has been correctly created.
We cannot answer anything simply without looking thru your equipment's connection. We hope you understand.
If installed wrongly and/or with wrong models, even the most expensive protector wont prevent your equipments kill by surge.

About the efficiency of the cal-lab and other *ahem* brand, please refer to post #4...

no such things that multi socket will lead the surge...
unless used poor quality multi socket or excessive cable extension to another location...
even though belkin come with multi socket version, still doesn't means it can against surge efficiently...

i sold many units of MDSC0039 with 1*3pin power socket, and most of LYN forumer used with multi socket, no complaint about this kind of combination...

This post has been edited by gkl83: Mar 4 2011, 02:15 PM

is the same performance as long as TPP and SP9201DAF located together...
but for this combination you can protect modem & telephone at the same time and same location