Try check out this url http://www.pureoverclock.com/Review-detail...360-radiator/4/
They did some performance review on the AX rad..quite good

This. Which is why I use a hair pin & trim it down. Next few months I will open a build log including the method I used

sorry blur pic.. going take one more

anybody wants pin removal tools from mdpc? haha.

I'm ordering some stuffs!

Fractal Design Arc Mini Case
ASRock Z77E-ITX
Kingston HyperX DIMM Kit 16GB PC3L-17066U CL11 (DDR3-2133) (KHX21C11T1BK2/16X)
Kingston HyperX 3K SSD 240GB
Intel Core i5-3450, @ 4x 3.7 GHz
Cougar GX G600 600W PSU ATX 2.3
Swiftech Apogee Drive II
Swiftech ⅜” x ⅝” Lok-Seal™ Compression Fitting
Swiftech Helix 120 Fans
Aquacomputer Airplex Pro 240 Radiator
Alphacool Cape Corp AGB2 Black Rev. 2 Reservoir
XSPC ⅜” x ⅝” (16/10mm) Tubing

Same as irie. I use stapler bullets as well. Cost saving but needs time to master it, just like irie said.
There are those stapler that are thicker and longer, get the job done easier and faster.
I do not know the exact measurement, need to check the box.

---

Added on December 7, 2012, 10:51 amHaha, yea, thats the molex convert to convert it to sata power for the disk drive. Lazy to sleeve that.
As for the cables right below GPU, yes they are casing wires.
I tried to sleeve them already, but seems to fail.
Any recommendation?

This post has been edited by Zheng87: Dec 7 2012, 10:51 AM

Owh man...bundymania from OC.Net joined us.. Already show some of them cool wasser kuhlung setup

wow nice, love the reservoir...and welcome to lyn

This post has been edited by Zzorro: Dec 7 2012, 06:08 PM

I am not sure about yours but mine some of the led wires can separate so its either I sleeve it individually till to the front of the case or get a sata sleeving & sleeve using that. I am not sure if all the wires can fit in there or not since I havent try yet but thats the solution that I can think of for my upcoming build.

Of course buying sata sleeving is a waste for that little wires unless you got already or wish to sleeve your sata cable as well...but what to do

I got bigger problem, mine the gpu wire got capacitor attached to it, so I cant sleeve individually without hiding the capacitor

silverstone strider?just cut the the 'capasitors'.

I searched for solution before many said the capacitor is there for a reason. To ensure quality voltages being supplied to the graphics card but cutting wont cause any negative effects though. I prefer to keep it

I think I might be able to hide it under the wires if connect the wires to the gpu from down, but only problem will be the luminous panel unless I cut a hole for the wires

extension is ur best solution.
cut mine so far nothing bad happen.

Hi Guys,

Just finished my custom WC setup..what a messy system I build..well at least there's no leak and the temp is good I'd be more than happy .



At the top of RX rad I put up 3 Arctic F12 PWM fans and connect them altogether then I connect them all to a molex to 3pin fan connector..Once the pc turned on, smoke comes out from the cable and it is melted/burned...

I dont think 12v 4pin molex cant handle 3 120mm fans right?

Is there a way for us who uses more than 12 fans to have better cable management e.g using molex to 3pin hub or some other way? I am using lots of 'molex > 3 pins' converter in order to connect afan..please help


update: ok found the splitter from molex to 4x3pin at frozencpu.com and they even got a molex to 9x3pin fan connectors

This post has been edited by shepard: Dec 8 2012, 05:11 AM

I'm using 4-Pin Power Distribution PCB 8xWay Block (MMT-PCB-4-83)



and

Phobya Y-Cable 3Pin Molex to 9x 3Pin Molex 60cm



All fans are running at full speed

New style gcwb link

Zzoro you sell burger now in ss15 subang jaya?

Nice , ok will place an order later. Thanks kevin

no other choice..I cannot fit a 1/2" 3/4" fittings on EK-FC7970 due to blocked by 7970's PCB. Since I dont have a thread extender and only got a 45deg rotary so I use it and this is the only way where I can connect between those 2 GC ....maybe have to drop by APES later to find small size extender.

This post has been edited by shepard: Dec 8 2012, 10:39 AM

yes bro.. let's visit and try our grilled burger tastes trutfulness...

This post has been edited by Zzorro: Dec 8 2012, 10:36 AM


Attached thumbnail(s)

let try this


Attached thumbnail(s)

im using this for the fans


This post has been edited by irienaoki: Dec 8 2012, 11:03 AM