sonicwall is not a cheap device.. surprise that it can't dail pppoe vlan correctly..

did u try to debug/capture trace when it tries to dail to see whats the fault ? for a device x10 more expensive than mktik..

i think u should at least try to troubleshoot it frist or get their customer service/support services...

ur sonicwall has an opt port right ?

if yes then the easiest way to configure rb250 is to zone it into two sections(segment it using the forwarding tab)

but with both still using vlan500 and you pipe the second unifi to your opt port and throw the dailer there..

This post has been edited by JinXXX: Feb 3 2012, 11:51 AM

i was mentioning the opt cause, im not sure your has wan2 port ..the opt port is configurable to be a second wan connection if u have wan2 then u can use wan2..

you just need to segment the rb250 into 2 and strip the vlan before connecting it to your sonic wan1 and wan2/opt

depends how your rb250 is.. the ingress port to tm needs the tag, if your stripping the egress to your sonic, then your sonic can dail without the vlan

unifi (vlan500) > rb250 (strip vlan500) > sonic wan1 (pppoe dail without vlan)

so the traffic will be pppoe > rb250 (tag) > unifi lan 500 > internet

of if you wan.. you can tag your wan port on your sonic for vlan500 and put the pppoe dailer there so when u dail and when it goes out the port it will have vlan500 and u can connect straight to the unifi(bridge)/fiber/vdsl



This post has been edited by JinXXX: Feb 3 2012, 12:35 PM

ur config wrong already la

u can't do it like that...

use vlan 500 for all.. but in the "forwarding" section.. you split the forwarding/cross connection table to split the switch into 2...

http://forum.lowyat.net/index.php?showtopic=1733801 , see post #4 & #5

the 501 vlan i was mentioning is to trunk 2 data line

This post has been edited by JinXXX: Feb 3 2012, 04:26 PM

well guess you solve your own problem,

when you login to the ATA adaptor, is it logged in to your voip provider ?

im guessing some network problem , open a new thread to address your problem this thread is for mikrotik only

This post has been edited by JinXXX: Feb 3 2012, 05:48 PM

can't comment about using the setup file, why dont you reset and configure it manually.. 1 by 1 following the screenshot ?

anybody using RB751U-2HnD

and have some weird problems ?

like this ?

not disconnection.. just packet drop.. just now i notice on my RB751U-2HnD

cpu hitting 100%,super slow logging to it using winbox, and im sure that is causing my earlier high tx drop rates..

fyi im using wired, got a feeling something is wrong with the firmware or the 5.12 os

nope

yeah doing that currently...

---

Added on February 5, 2012, 11:46 pmanybody know how the heck to read the supout.rif file ?

This post has been edited by JinXXX: Feb 5 2012, 11:46 PM

go check the wiki regarding chain..

input (refers to router itself)
forward (pass through router)
output (well the opposite of input)

go to the ip>firewall > connection and see how many connection are there...

me 1 user can have about 300 max.. and on average 150 connections

@weikee , cisco IOS , can do scripting ?

This post has been edited by JinXXX: Feb 12 2012, 04:46 PM

if not mistaken you need to create a new network and have a route to route it in

as the ip assigned to the router will be the gateway...

you need to create another network with the proper subnet of the public ip i think its /26

if not mistaken usually the ip assigned to the pppoe interface

is the gateway to your other ip that is given..

nope.. never did found out and nobody seems to know anything abt it.. other than some people are experiencing it..

im guessing its a bug.. not sure if it exists on the new 5.13 but seeing the mk forum..

seem like 5.06 and above seem to have weird funny problems..

maybe u can help bump the thread in mk forum see if anybody tested out the 5.13 and is still having the problem or not

ps : i malas wan to test and swap back n forth.. just need my network to run and work..

This post has been edited by JinXXX: Feb 17 2012, 02:36 PM

nope check already..

those batches are in the very early stages of the release way back in oct/nov...

http://wiki.mikrotik.com/wiki/Manual:IP/Address

ip address> add address=10.10.10.1/24 interface=ether2

so u guys would put

tmnuts ip/30 interface=ether3 well 30 is already 1 ip with 1 loop and 1 bcast..

so /29 will net you 6 ip.. 1 on the pppoe interface aka gateway to your other ips..

then from then link out to a switch and pop the ip's to the server or what ever net equipment ?

anybody tested that ?

should be able to route the traffic in and out of the router since the pppoe for biz is usually the gateway

which happens to the be the first/second ip of the /30 right, (depending if you count loopback)

hey test out your RB751U-2HnD with unifi and tell me if your experiencing the problem that i had earlier

wan see whats the problem/fault

use the "snoop" function to see the wireless channel at your place/area..

my condo is super congested with wireless signal

i didnt use btest..

the data was from connected/running on internet...

which version of mikrotik you are using ? 5.12 ? or 5.14(latest) ?