will post my new updated cable management soon...

Cut a hole behind your mobo tray.
Push as many cables as possible to the back of the case.

Fold the IDE cables and push it under your hardrive.
Else, slice them up and cable tie them. Then pull it to the edge of your case.

The cables, can also be pushed into the 5.25" slots if you refuse to cut a hole on your case.

wahahahah. like this oso can ar? got preview 1st or not?

preview u can view last few thread on my old cable management ler....
jz wait i got time to snap some pics n post it up..

Hi again guys. This time, I'm posting up my fren's TT Tsunami dat we worked on last Saturday.. here goes the before and after..

BEFORE



AFTER


Personally, I think dat white PATA cable should be change wif rounded ones... but datz up to my fren la ryt? btw, those sleevings and molex are UV reactive... but he decided to give me his UV CCFL.. not sure y but yeah, i got a new UV CCFL now.. time for me to pimp my pc back into the UV arena.. ahhahaha.

any comments are welcomed to improve the tidyness.. but I gez I haf to make my fren visit this thread coz I ain't going to Melaka juz to tidy up his cable... ahhahaha.. jk jk

a very nice...can the flat ide cable be hid? if it can be hide i thk better use rounded ide cables..others is fine...

Where are the UV CCFL ??
Why not post a pics when on night and with UV on

kenot oredi.. coz the hdd IDE is not dat long, n already been twisted(to make it look round) by the owner. rounded cable indeed then...

he oredi gave me his ccfls... dat, I'm not sure y.. but he's not a UV enthusiast anyway.. r u, disket? he juz wanted me to spank all his cacings oni.. but for future expansion, make all the sleeve UV-ready.. ewah~

I wonder if anyone had tried to make their custom ide cable.. do u think it can be done? I went to n electronic shop @ Jln Pasar, found lotsa wide-cable-ribbon(the one like IDE cable) there.. any worklogs dat i can refer to guys?

p/s: i wonder if he wanna give a say here.. kamon baby, u can do it... kamon la disket.

This post has been edited by r4ydc24: May 17 2006, 09:22 AM

what disket lolz ??
you can slice those ribbon IDE cable and then tie them up just like rounded IDE cable though

alo alo, that's my case there . r4ydc24 helped me do all the work while I just sat there passing the tools to him

I'm not really into pimping my PC heh, just wanted to make it look nice and have better air flow. Prolly will get myself rounded IDE cables soon to replace my old cables

comments plz...

finally, after long period of waitings... uhuhuhuh
woh, how come ya casing got 1 hell of a spacious mobo tray ar? or was it ya mobo is kinda small?

i can see a lot of cable ties involve.. not planning to sleeve, my man?
the molex for gfx card, y not connect it from the back of ya hdd tray? so dat u can also hide the molex for ya upper hdd, n ya intake fan as well.
the red sata connector, try reroute it to appear from under ya bottom hdd. as for me, i wud prefer for the gap between those 2 hdds to be clear.

gez datz all from me,till i haf mo ideas..

nway, nice neat mobo area man...

cool...i luv ur ideas...
FYI my mobo is a bit smaller... its the low end models...tats y a bit small...hehe..
i was thking of cables sleeving...but i got no experiences...scared might f*** up the whole thgs...
i will try ur idea..but wanna let u knw tat the cables tat u can c is not the intake fan ones...its the exhaust fan at rear...i tarik all d way to frnt...
the intake fan cables is on the other side of the hdd tray..

comments plz...

[/quote]

I think what you can do if u are scared of sleeving using those sleeving kit .... maybe u could just heatshrink it...

it is much cheaper then sleeving kit as well...all u need to do just fit through the cables and get a hair dryer to shrink it to the size of ur cables....done !!

for better result keep ur zip tie so that after the heatshrink shrinked it would not move around ...

as for the sata cable u could route from bottom instead of going through the gap between two HDDs...it is better for airflow as well...

same goes for the rear exhaust fan power connector and the gc power connector if u could get longer cable....

as for the IDE cables if u dont want it to be so obvious u could actually fold it in zip zap manner and hold it with some tapes...the best is u could also just heat shrink it for better holding....

ee.e.e.e.e..e.e..e.e.exhaust? datz lyk the WHOLE 9 YARDS man.. ahhahaa.. so far u tarik ar? what i normally do wif the exhaust fan cable is to bring it to the back of the mobo via the gap at the PSU area.. then, behind the mobo, u can cincai bocai connect to any molex loh.

I support Doom's idea regarding the heatshrink thingy but u hafta remember 1 thing bout heatshrink, is to use proper size heatshrink to make it too nice.. if not, it'll be lyk the blue heatshrink i used for my SATA connector, which ianho once talked about. back then, i got not enuff heatshrink to play wif... ahahahha.

If I were u, I'll juz spray the ATA cable (UV mebbe) and drop some kewl stickers on it... it looks awesome to me already as, if itz in dark, it'll look like a panel... 2 panels in ya case....juz make sure it is straighten remarkably ar... uhuhuhuh. then stick ya computer sticker or wat not...since i think ya ATA cable is nicely position near the mobo tray liao.

if everyone can focus on the 2nd pic now... CLASS~~~ your attention pls... .. the Power LED, Speaker blablabla connectors can be sleeved lyk the those black heatshrinked cables u got beside em... sleek n neat.. black long heatshrink + grey short ones, juz lyk factory-sleeved..

the reason he doesnt wanna do sleeving is because hes worrieed hell screw it up...u guys asking him to use heatshrink...hell basically have to do the same thing as sleeving oso wat.... might as well just sleeve... itll look way better imho

EDIT: silap type

This post has been edited by mADmAN: May 23 2006, 10:52 AM

but sum ppl juz dun wanna deal with the sleevings.. u kno laa, the serabut2 kinda thing... n put all the wire into it... then heatshrink pulak not tight enuff... as for only heatshrink, sum sizes, u dun hafta remove the connectors ryt? but that case, u hafta deal wif the sizes 1st la ryt..

typo edited

This post has been edited by r4ydc24: May 23 2006, 11:24 AM

That's why it is easier to heat shrink them sleeve since u dont need to remove the molex connector ..... while heat shrink only need to get the desired size only ...

getting black heat shrink is easy men , any size but only one color....

lolx...i dont understand what are you trying to say

This post has been edited by LittleLinnet: May 23 2006, 02:41 PM

yea dude...i got experience n i scared totally screwed up the whole thg...
if i were to do ths thg..wat wat madman says i might as well sleeve..
but anyway i like u guys idea...can i knw whr can i get those heatshrink?
and also i thk heatshrink oso need to remove the molex ler.. if not need use bigger heatshrink ler...n after tat not nice wor..


me too...dunno wat he mean..