thanks, i was so into panel lining and 'accidentally' put too many line. looks cacated edy
need to find thinner pulak after this
those hard to reach places maybe could use tweezer + cotton

can if the lining not too thick

This post has been edited by nazrul90: Jul 18 2011, 04:34 PM

maybe scrub it while submerge underwater?
warm water? think ill try it later tonight

u can try zippo lighter fluid too. works as well

one thing i can confirm is i use bamboo tooth pick (have sharp point at both side one) before to clear the lining in RG before, dont worry, the tooth pick is softer than plastic.

thanks, but i dont smoke so no use afterwards
but if cheaper than thinner maybe i will buy

will try those too, i think still have some left in the kitchen. unused ofcourse

art student also got use zippo to remove the glue stuff on artwork also la

i am no art student la

btw OT:
bought ace hardware art knife yesterday and when i turn the bottom of the handle to tighten the blade, it slipped and become loose. is this normal or mine broken edy?

---

Added on July 18, 2011, 5:44 pmwhat i mean is i can put the bottom back to the stick inside, but cannot make it too tight cuz it will become loose again.

This post has been edited by dfcloud: Jul 18 2011, 05:44 PM

i think you better post a photo about your knife. i really dont get it haha

later i arrive at home ill post it here

I used to buy this kind of knife before. I will become loose in no time.
So my advise is, just spend a bit more, buy Tamiya @ Olfa Design Knife.
Olfa one around RM28 (with 30pcs blade).
That one u can use for a year ++. I bought my Tamiya Design Knife on 2009 till now not yet finish all 30pcs. Its really worth buying la. More value for your money rather than u buy the RM10 or less knife than cannot use properly.

U can buy it here.

This post has been edited by afsarudy: Jul 18 2011, 06:10 PM

If u visited Mid Valley Ace, better walk a walking distance to Jusco...I'm still using the RM8 one, no loose & still ok until now but for sure the Tamiya Olfa is much better

If you want to use thinner or the zippo lighter fluid, best test it on your runner first.

sry to ask this question here but does there any plamo kit
for any Metal Gear ? primary REX and ZEKE
since metal gear is also a mecha so i think is suitable to ask here cuz
wat i'm searching is plamo kit

This post has been edited by calcilis: Jul 18 2011, 07:15 PM

zippo is quite mild. a lot of ppl use it for enamel paint washes. so even if u dont smoke there're plenty of uses for it. and it's way cheaper than any modelling thinner i've seen.

i'd wan a peacewalker!!
Zeke will have trouble standing leh

now that u mention it
ZEKE has an EXTREMELY small foot hold

REX is not problem its foot consist of 1 large part and 1 small part
so its like standing on 4 legs althought there onli 2 legs
as seen on this photo


This post has been edited by calcilis: Jul 18 2011, 07:34 PM

wow nice... Rex is the one firing nuclear weapon right? Ray only high-tech pew pew laser?

@dfcloud,

becareful if using thinner, the way they clear the marking is to wipe out a very thin layer of the plastic. So the more you use the more damage to the part.

---

Added on July 18, 2011, 8:44 pm

Am thinking if MG 7 sword come out, buy it and re-paint it with metallic color. (With whatever gundam color spray/ tamiya color spray can) might get far far cheaper? (Most probably wont exist rm250)

yes tuan...
(Look at the pic, do you all think that the details are very very good?)

This post has been edited by Vorador: Jul 18 2011, 08:47 PM

if i remember ray don use laser
it suck in water and fire a highly pressured water cannon while pin [point it in a small stream of water jet
its small but can penetrate military grade armour

oh... so that one is sea water then... last time when playing use to run run and run to dodge the beam attack.