nice new build up kevin. anyway, this wc stuff you call it mid end kit?

Interesting result to share...

Fuzion v2 vs Apogee XT.

Note that this is an full of error result, Fuzion setup was with DD CPX-Pro Pump + BitsPower Reservoir + 7/16ID" tubings

XT setup with XSPC Reservoir Top + MCP355 + 3/8" ID tubings.

Ambient error around 1-2c, non aircond, guess ambient cannot run too far since i have no aircond and are in indoor location.


The result with D-tek Fuzion v2


The result with Apogee XT

This is just a rough comparison based on screenshots i owned, not an experiment purposely to take the readings.

Radiator setup were the same, both on Single 120mm Syscooling Copper Radiator on my very light and small WC setup.

This post has been edited by lichyetan: Dec 20 2009, 03:43 PM

Uish, 10 feet of Tygons is too much la bro. 5 is enough

This post has been edited by tesla_rage: Dec 20 2009, 03:55 PM

zzz... mid end? sure sure

By the way, just for anyone who owns CM ATCS840 or someone whom u can tell to..

The HDD cage actually couldn't hold a dual rad. As the height of the dual radiator exceeds the height of 2x 120mm fan. coolermaster didn't allow enough space to place a dual rad at the side of the HDD cage. My swiftech dual rad fitted (barely), coz I forced it in REAL REAL HARD. but it was totally impossible with feser dual rad due to its extra height

Based from my trial and errors, the side of the HDD cage of ATCS840 is better suited for single radiator

This post has been edited by metsatsu: Dec 20 2009, 03:59 PM

bro, ur apogee XT inlet mcm got problem, you used the top as inlet or the mid ?

The exchange rate is 3.5 now I can get everything listed here for you at RM1890 with 2 exceptions:
1. You'll get EK250 instead of Bitspower Z Water Tank
2. Standard MCP-655 pump (if you want to mod yourself: http://forums.pureoverclock.com/showthread.php?p=35299)

Plus, I'll throw in a 5% discount so that's RM1895 - 5% = RM1800. All in all, it's even cheaper or more/less the same with Sidewinder but with advantage:
1. You don't have to wait 2-3 weeks shipping without proper tracking

Water cooling is fun especially when it's affordable

This post has been edited by clawhammer: Dec 20 2009, 04:54 PM

Omfg, epic mistake!!

Thx for pointing it out. This is the consequence of not doing enough reading...

Shit now i will have to remount the wb again... Hope i still have enough tube left

This post has been edited by metsatsu: Dec 20 2009, 05:59 PM

lol... the XT wb position is different from GTZ when mounting on i7....

Yea, the inlet for XT is the one with rotatable plate

Let us know if you need extra tube. I am sure someone here can help.

---

Added on December 20, 2009, 11:10 pm

Still haven't include 45 and 90 degrees rotaries. Say if he needs 4 of these... then it means he needs another 4 compression fittings

The joy of water cooling cosmetics.

He would need a GPU block though. CPU cooling only would be less challenging

This post has been edited by tesla_rage: Dec 20 2009, 11:10 PM

Yup but it's more or less the same as rotaries are being sold at a very expensive price even at cost from Bitspower Maybe quality products are always like that, lol.

Managed to change the inlet/outlet by rotating the wb + tube rerouting. The end results were 1c drop in all cores, swollen fingers, messy room and a sore back. Will upload some screenies tonight

Great work Ee Seng Why not you dismantle everything and do it again? Maybe there'll be temp drops?

Lol. How about u come to my place and redo everything for me, FOC? And we'll see who's gonna get peeled fingers and broken back. Maybe then i'll consider bringing u to tambun for ur little effort.

haha... setting up wc pc can spent whole days one... especially large loop...

Better watch out ur gf cos claw is hamsap one ler.
Ohh no wonder lah claw said wanna come over to pg tomorrow.

---

Added on December 21, 2009, 8:59 pmI'm still considering installment plan offered by claw

This post has been edited by owikh84: Dec 21 2009, 08:59 PM

Really? then sorry MR ONG, no free hawker food for you bro.

@owikh84
u should go for the installment plan.

Here's my corrected inlet/outlet apogee xt (sorry for the dark and blur picture, i don't have a digi cam)


Attached thumbnail(s)

OT:tambun?for seafood?

Tambun Lost World?

yes, THE Tambun for seafood. luckily he decided to go by himself

by the way, managed to grab my brother's digi came for a quick snap.

Well done metsy. Those temps impressed me.
Good VTT too mine 1.3xv huhu