guys, i got this old car... saga magma..
want to send repair, which bengkal u guys recommended somewhere pj area,
which not expansive lar and good service.... any idea guys ?

how do i change DIY coolant. advice please

true.......

Notoriez,
for my opinion la..... no offense la
Block 1.5,new 1.6 stroker kit,new valve,new conrod,new crank total cost also 5k.
+performance cam,ACP,LCP,clutch set new. 2-3k edi. do balancing + installation 2k +-
if injection some more + emanage blue.....

u count la..how much it will do.......

parts r not easy to find. some more 2nd hand woh.......

This post has been edited by boon-boon: Apr 9 2011, 02:25 AM

i got 1 at old town
mau ???

---

Added on April 9, 2011, 4:21 amyou open ur rad cap and the nut below ur rad kasi the water flow out then refill again
or you want do more total flush go disconnect both upper and lower hose and use ur garden hose kasi water flow inside until clean then plumb back


This post has been edited by sinister_sid: Apr 9 2011, 04:21 AM

Hi guys ,

I plan to change my stock rim to this R3 rim.I am not sure if it can fit on my saga,07.
I think it would be very low after putting it in.
Anyone could en light me on this .
Where could i get these and price also.Thanks

will get some carbie cleaner to clean it...

no la...dun really floor it when cold start...only after the engine warm up already then only will floor abit more...

oh...gotta go back to the mod shop later...

my exhaust sound not that loud so the high pitch still very obvious....think gotta change to the jasma n1 exhaust (any review or comment on this muffler)

for the fuel will check all the rubber seal....

u know how much anot the price
can buy my saga liaw la

---

Added on April 9, 2011, 2:55 pmpicture not yet upload my phone cable putus liaw

This post has been edited by sinister_sid: Apr 9 2011, 02:55 PM

where u wanna find new stroker kit??... crankshaft all second item.... conrod can use back ur 4g13/4g15 ones... piston u can go for new oversized ones... else, original 4g18 piston bore size also can d.... u need new piston ring... conrod bearing change or not depend on the condition of it... if wanna do 1 shot den change together gether....
no need new valve laa.. unless u going for oversized valve with 3 angle cut den different cerita....
performance cam approx rm700-900... ACP+LCP approx rm300... clutch set 1.6 with ST flywheel approx rm350-400.... balancing no need laa....
injection + emanage around rm3.5k....

http://www.zerotohundred.com/newforums/cha...d-s1k-rims.html

any thing newer masuk our 4g15 called new lo dewwwwwwwwwwwwwwwwwwwww

planning to install ACP + LCP works engineering product in my lmst 4g13 . any reviews on this sifus ? Acceleration wise improve alot right ? and i heard that top speed will go down is it true ?

Thanks for all your helpssss sifussss





http://www.mudah.my/Works+Engineering+Cran...ley-8665117.htm



im still confused lols on the ACP after reading all over forums all the bad reviews i seldom see good reviews may i know sifus here those who are using ACP what brand are you guys using ?

Thanks alot in advanced .

This post has been edited by Peekab0o: Apr 9 2011, 05:51 PM

i suggest u buy better rim than this rim.... this rim is looks ONLY...

install the LCP 1st then baru install ACP + regrind cams ma.....

LCP juz help u to improve your low end... might increase HP as well....

ACP is to tune your powerband, either u want low end more power or high end more power....

U decide.

post the pics after putting it

thanks sifu...

so LCP dosent have to worry about anything.

ACP is a big headache
I guess cant find a good tuner to do the ACP = Gonna get headache with my engine right ?

No headache if tuned nicely....

headache malii if tuned sucks.....

thank you for your answers.


Finding tuners for ACP in Johor Bahru .

Sorry should hose to under paip below manifold
not thermostate




This post has been edited by sinister_sid: Apr 9 2011, 10:58 PM


Attached thumbnail(s)

nice choice you have there

i m currently using Works ACP and Mytheology LCP...it will definitely improve your torque. BAD REVIEWS..??
My advise, go to workshop that really know how to tune ACP...beware coz alot of sinkalan outside

hi every1..i would like to ask any nearby mechanic who is more pro in this saga...im staying in sunway area..would like to get a check up for my car

---

Added on April 10, 2011, 2:05 amhi every1..i would like to ask any nearby mechanic who is more pro in this saga...im staying in sunway area..would like to get a check up for my car

This post has been edited by hanzzz: Apr 10 2011, 02:05 AM

why not new stroker kit? u kasi telan if i found it?
i can dapat everything new... u wan anot? anda berani?