done check with nb heatsink..got that yellow termal paste...
OC cpu temp load 55c and idle 38c for 3.4Ghz...at 1.26v..

is it ok with that?

last nite fiddled around again, and i got this... 1.224v for 3.9GHz. tried 1.215v but prime95 shows error, and system restart shortly after that.

bclk 188 with 21 multiplier, running on 1.224v. prime max temp reaches 91 last nite. but the temp was quite ok i think, average 85.

Lol, my 1.3V already for 4Ghz

ic ..coz my stock Vcore 1.22v..
i just change my bclk 170 with 20 multiplier..
me still new in OC...

hmm... should i upgrade my cooler? the new super mega looks extremely delicious if fitted with a pair of silverstone fans.

hope can bring down the load temp to around 60+

Nahh, unless you applied low voltage & also in AC room. Else, it just bring minor difference..

do you think max load with 80 degree achievable? my v8 max getting 95 degree, but average at 85~90.

to bring it to 60+, go for water cooling

you can reduce 3-5c if you switch to megahalems.. ( my guess only )

hmm... 5c... doesn't sound like a good investment for rm300+. maybe i'll just get my lazy ass up and clean my dusty rig.

Get WC laa, can OC to the max!!

did WC really good meh?

don wan lar... water cooling very mafan... need to constantly monitor the reservoir, and scare of water leaking. and if upgrade, wan drain water again...

you will fall in love with it....trust me....

This post has been edited by selfdz87: Nov 8 2010, 07:04 PM

i do fast OC n i get this want >>



want to ask, is my qpi/dram is safe voltage? i try from 1.25 ~ 1.47. this 1.47(set in bios) is stable and can boot.
my timing,any advice guys?

google told me dat as long as u keep da voltage less than .5V between qpi n dram.



This post has been edited by kolong: Nov 9 2010, 01:25 AM

Good job on the clocks.
That high QPI/dram aka vtt is normal for R3E. Just make sure that all OCP settings are enabled in bios to avoid explosion
On stock cooling it's best to keep it below 1.55v. Get a table fan blowing towards ur casing while stressing.
The vtt that actually killed me R3E was 1.6Xv OCP off, on stock cooling.
On EVGA Classified my 920 @ 4.2Ghz HT ON, uncore 4Ghz, dram 2000Mhz, can go as low as 1.425v vtt
uncore 3600Mhz, dram 1600Mhz, 1.3Xv vtt

P/S: ordering Classified3 E770 from karom

Haa? OCP?? Wut is dat? Duhh..I still don't know a lot of thingbro owikh...


EDIT: ok..i got it ody. its enable dy. hehehe..

This post has been edited by kolong: Nov 9 2010, 11:11 AM

R3E stock cooling does not cover the vtt mosfet chips, if over volt heavily, it will burnt easily... I experienced it when using EVGA SLI micro, stressing at high vtt without cooling on vtt mosfet chip. If wanna run high vtt voltage, cooling on the mosfets are required.

ermm..thinking want to get full mobo waterblock. izit the block will cover the mosfet as well?

I replaced stock cooler with Hyper 212+.


This is before replacement. Exact same settings.

mine i7 920 3.6gHz on 1.2v ..temp load +-60c.idle +-40c...
is it ok??