QUOTE(8zelk8 @ Oct 11 2010, 09:44 PM)
4 ur info, currently 2nd hand price still about 5k++ if new maybe 7K++or below 4 ss version aka no hand clutch. coz i'm also looking 4 2nd hand lc.
But the website shows only RM 6k+ The price still so high
^^==>LYN Yamaha 135LC Club V6<==^^, >>>Ridershood Spirit Continues<<<
|
|
Oct 11 2010, 09:54 PM
|
![]() ![]() ![]() ![]()
Senior Member
633 posts Joined: Jun 2008 |
|
|
|
|
|
|
Oct 11 2010, 09:58 PM
|
![]()
Newbie
0 posts Joined: May 2010 From: Turtle Island |
|
|
|
Oct 11 2010, 10:13 PM
|
![]() ![]()
Junior Member
199 posts Joined: May 2008 From: Selayang Mall/Hosp. Selayang |
try to get new one la...so u will know what the prob that cause by you not by old user....
new one..RM6k...[used bike would cost 5k+] IN PLANNING TO SELL PERFOMANCE PART FOR LC135,KRISS,GT128 ETC....END OF THIS YEAR...WAIT YAHH... block,cam,valve spring etc..etc.. This post has been edited by machai_world: Oct 11 2010, 10:46 PM |
|
|
Oct 11 2010, 11:44 PM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,879 posts Joined: Jan 2003 From: Medan, ID |
QUOTE(Aaron135LC @ Oct 11 2010, 07:08 PM) yea... buy projector... can buy hid set ade... chances of melting drop significantly... Thx man. Just like most things, even headlights can be quite complicated. To simply put it, a good headlamp illiuminates the road ahead, with a good cutoff against incoming traffic, but sufficient high light to illuminate against danger from far ahead. No glaring, long bulb/ reflector life, low power consumption etc...btw.. bro alex.. u know wat.. i always tot projector is not brighter than stock reflector.. cause of the projector glass.. the light 100% cannot penetrate.. instead only left 80% of brightness.... u can see in cars... savvy n waja wan light.. savvy wan is direct reflector.. enough to make u blind.. with stock bulb.. waja wan soso nia... Example: Riding on dark highway using low light. if use normal lamp, if there's something up ahead, the normal light will agak agak reveal it to you. With HID, the cutoff is perfect and you won't see it at all. If you take a look at original headlamp, the bulb will installed slightly slanted to the right. This is because halogen bulbs have a built in cutoff that looks like a mangkuk, and when you turn on low light, the cutoff will look diagonal where the right side is lower, to prevent shining against oncoming traffic. Halogen bulb not suitable for projector headlamp because it's simply not designed for it. This bulb has filament, instead of a glowing spot like the HID bulb. So, the projector will "magnify" and "project" the filament onto the road and effect will be like one spot one spot here and there... |
|
|
Oct 11 2010, 11:49 PM
|
![]()
Newbie
0 posts Joined: May 2010 From: Turtle Island |
QUOTE(alexei @ Oct 11 2010, 11:44 PM) Thx man. Just like most things, even headlights can be quite complicated. To simply put it, a good headlamp illiuminates the road ahead, with a good cutoff against incoming traffic, but sufficient high light to illuminate against danger from far ahead. No glaring, long bulb/ reflector life, low power consumption etc... nice info alex, btw here's the gd news 4 125 rider>>>>My WebpageExample: Riding on dark highway using low light. if use normal lamp, if there's something up ahead, the normal light will agak agak reveal it to you. With HID, the cutoff is perfect and you won't see it at all. If you take a look at original headlamp, the bulb will installed slightly slanted to the right. This is because halogen bulbs have a built in cutoff that looks like a mangkuk, and when you turn on low light, the cutoff will look diagonal where the right side is lower, to prevent shining against oncoming traffic. Halogen bulb not suitable for projector headlamp because it's simply not designed for it. This bulb has filament, instead of a glowing spot like the HID bulb. So, the projector will "magnify" and "project" the filament onto the road and effect will be like one spot one spot here and there... |
|
|
Oct 12 2010, 12:30 AM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,879 posts Joined: Jan 2003 From: Medan, ID |
wah, forged rims... nice!
everything forged: piston, block, and now sport rims... |
|
|
|
|
|
Oct 12 2010, 10:55 AM
|
![]() ![]()
Junior Member
191 posts Joined: Jun 2008 From: Sand Village |
selling lc 135 2nd 1st model here..
pm me if anyone interested.. 4.5k.. |
|
|
Oct 12 2010, 10:56 AM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,879 posts Joined: Jan 2003 From: Medan, ID |
So, anyone know where to buy the projector lens?
If got cheap deal, I can help you make it also... |
|
|
Oct 12 2010, 11:07 AM
|
![]() ![]()
Junior Member
64 posts Joined: Apr 2008 From: Penang |
|
|
|
Oct 12 2010, 12:19 PM
|
![]() ![]() ![]()
Junior Member
360 posts Joined: Nov 2009 From: Penang |
QUOTE(Spayz @ Oct 12 2010, 11:07 AM) yea hor!!! how much is it..? can find 1 with pricing..??Added on October 12, 2010, 12:22 pm QUOTE(alexei @ Oct 12 2010, 10:56 AM) if cheap.. i go find u ade.. + installation for HID... dunno expensive or not..dunno police block or not.. haha This post has been edited by Aaron135LC: Oct 12 2010, 12:22 PM |
|
|
Oct 12 2010, 08:02 PM
|
![]()
Junior Member
9 posts Joined: Feb 2009 From: Greenlane Area,Penang,M'sia |
Wa if we pakai this http://www.alibaba.com/product-gs/30195762...le_muffler.html then stick YOSHIMURA i think we can pass through JPJ d
|
|
|
Oct 12 2010, 11:43 PM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
4,060 posts Joined: Jan 2003 From: Penang / PJ |
QUOTE(bizzy123 @ Oct 12 2010, 08:02 PM) Wa if we pakai this http://www.alibaba.com/product-gs/30195762...le_muffler.html then stick YOSHIMURA i think we can pass through JPJ d wah, this tail pipe nice !my bike is ok now.. btw, able to do 130kph GPS speed easily on the slight uphill stretch in front of NBH shop (abt 400m distance). top speed is 136kph GPS, limited by sprocket (ady 10krpm 4th gear). Using cheaplak EO from Tesco and normal fuel. I'd consider this as good result. sometimes i still hear engine knocking, perhaps water leakage again.. really scared liao btw, big block like 60mm is fine, just stay away from compression ratio modification (as in shave cylinder head). This is giving me and BH a lot of headache. Added on October 12, 2010, 11:44 pm QUOTE(alexei @ Oct 12 2010, 12:30 AM) I wana change to 180 rim rear and 160 rim front... still saving money ^^hmm... dunno when will have forged body kit, lol This post has been edited by charge-n-go: Oct 12 2010, 11:44 PM |
|
|
Oct 12 2010, 11:56 PM
|
![]()
Newbie
0 posts Joined: May 2010 From: Turtle Island |
QUOTE(charge-n-go @ Oct 12 2010, 11:43 PM) wah, this tail pipe nice ! means really like tht liao since hv done so many touch up on the block. maybe its fate gua since u hv reach 136gps speed. if ur sprocket drop to smaller, i think top speed more higher add about 20 or less kmphmy bike is ok now.. btw, able to do 130kph GPS speed easily on the slight uphill stretch in front of NBH shop (abt 400m distance). top speed is 136kph GPS, limited by sprocket (ady 10krpm 4th gear). Using cheaplak EO from Tesco and normal fuel. I'd consider this as good result. sometimes i still hear engine knocking, perhaps water leakage again.. really scared liao btw, big block like 60mm is fine, just stay away from compression ratio modification (as in shave cylinder head). This is giving me and BH a lot of headache. Added on October 12, 2010, 11:44 pmI wana change to 180 rim rear and 160 rim front... still saving money ^^ hmm... dunno when will have forged body kit, lol |
|
|
|
|
|
Oct 13 2010, 12:04 AM
|
![]() ![]() ![]()
Junior Member
360 posts Joined: Nov 2009 From: Penang |
QUOTE(charge-n-go @ Oct 12 2010, 11:43 PM) wah, this tail pipe nice ! u know ur 136 is how fast boh..???? LOLOLOLOLOLOLOL....my bike is ok now.. btw, able to do 130kph GPS speed easily on the slight uphill stretch in front of NBH shop (abt 400m distance). top speed is 136kph GPS, limited by sprocket (ady 10krpm 4th gear). Using cheaplak EO from Tesco and normal fuel. I'd consider this as good result. sometimes i still hear engine knocking, perhaps water leakage again.. really scared liao btw, big block like 60mm is fine, just stay away from compression ratio modification (as in shave cylinder head). This is giving me and BH a lot of headache. Added on October 12, 2010, 11:44 pmI wana change to 180 rim rear and 160 rim front... still saving money ^^ hmm... dunno when will have forged body kit, lol my biek now tops at around 113 i think.. after install this New meter.. din try ade.. |
|
|
Oct 13 2010, 12:22 AM
|
![]() ![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
4,060 posts Joined: Jan 2003 From: Penang / PJ |
QUOTE(8zelk8 @ Oct 12 2010, 11:56 PM) means really like tht liao since hv done so many touch up on the block. maybe its fate gua since u hv reach 136gps speed. if ur sprocket drop to smaller, i think top speed more higher add about 20 or less kmph haha, now I am using 15-37, I think 15-34 is more suitable. Perhaps can increase pickup even more since 1st and 2nd gear can pull longer. QUOTE(Aaron135LC @ Oct 13 2010, 12:04 AM) u know ur 136 is how fast boh..???? LOLOLOLOLOLOLOL.... me ride till 120 scared ady. Joki help me reach 136kph one.. my biek now tops at around 113 i think.. after install this New meter.. din try ade.. |
|
|
Oct 13 2010, 12:33 AM
|
![]() ![]() ![]()
Junior Member
360 posts Joined: Nov 2009 From: Penang |
Added on October 13, 2010, 12:34 am QUOTE(charge-n-go @ Oct 13 2010, 12:22 AM) haha, now I am using 15-37, I think 15-34 is more suitable. Perhaps can increase pickup even more since 1st and 2nd gear can pull longer. hahha... next time who wants to try TS.. can ask joki go try ade.. but must make sure ur bike comes back in 1 piece la.. and not in pieces... hahahme ride till 120 scared ady. Joki help me reach 136kph one.. suppose use 34 like that ade.. cause now is 60mm block.. Added on October 13, 2010, 12:44 amthere is a new lc on the loose.... have a look at this link... newer facelift.. http://www.kaskus.us/showthread.php?t=2700042 http://tmcblog.com/2009/11/05/serdadu-neo-...ta-baru-yamaha/ This post has been edited by Aaron135LC: Oct 13 2010, 12:44 AM |
|
|
Oct 13 2010, 04:52 PM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,879 posts Joined: Jan 2003 From: Medan, ID |
QUOTE(charge-n-go @ Oct 13 2010, 12:22 AM) haha, now I am using 15-37, I think 15-34 is more suitable. Perhaps can increase pickup even more since 1st and 2nd gear can pull longer. hey, welcome back to the green monster.me ride till 120 scared ady. Joki help me reach 136kph one.. riding like this, how long will the engine last? To measure GPS speed, do you need to maintain the speed for a few seconds to get a good reading? This post has been edited by alexei: Oct 13 2010, 04:53 PM |
|
|
Oct 13 2010, 05:06 PM
|
![]() ![]() ![]()
Junior Member
360 posts Joined: Nov 2009 From: Penang |
QUOTE(alexei @ Oct 13 2010, 04:52 PM) hey, welcome back to the green monster. in our meter... as long as the reading hit the top.. it records down ur max rpm + TS... even if it reaches for less than 1 second... it still records down...riding like this, how long will the engine last? To measure GPS speed, do you need to maintain the speed for a few seconds to get a good reading? |
|
|
Oct 13 2010, 05:54 PM
|
![]() ![]() ![]() ![]() ![]() ![]()
Senior Member
1,682 posts Joined: Jan 2007 From: Kuala Lumpur |
guys suggestion place to get 135LC es around klang valley. or maybe KL laa.. i check at kok motor, in house loan rm 3.3k and RM 200 for 2 years. i dont want aeon or singer.. a little bit expensive. if got please state down here ar..
|
|
|
Oct 13 2010, 06:11 PM
|
![]()
Junior Member
9 posts Joined: Feb 2009 From: Greenlane Area,Penang,M'sia |
The LC was launched in Indo long time d lo, check T135 alot of this stuff will be posted up...
|
|
Topic ClosedOptions
|
| Change to: | 0.0188sec
0.41
6 queries
GZIP Disabled
Time is now: 30th November 2025 - 11:28 PM |