i dun think so. unless u prove it to me.

This post has been edited by sharkeer: Nov 26 2009, 02:25 AM

let it try at 400FSB first. i wish to know too :}

You can always play with the memory divider to gain 400+ FSB.

the question is, can this proc hit 400mhz above?

All the Bro, i just try 2, 3 time for the moment......cann't hit to 400mhz.....via i lower down the multipler or increase the FSB, can not, just max to 335 FSB, may be it should add up voltage or VID......i will not yet try it....

TQ!!

This post has been edited by kimtee: Nov 29 2009, 08:03 AM

dont bother. probably hits the wall edi.

Maybe you need better board . Board that can adjust GTL to 0.69/0.71 .

try pin mod your E32, if it still cant go over 335mhz, tat's ur processor fsb wall.

All my bro, yah...loh....oledi hit the fsb wall.....cann't up to 335fsbwith 12 multipley.....nasib.....
but cukup untuk saya....leh.....tak tamak......4Ghz is OK.....

My board can adjusting GTL, but try oledi....may be need better MB, cost this one not the very good OC board....but OK to me lah...

OC= Overpower, Costlower .... for the orang miskin.....

kimtee,see your celeron is very good in the o/c result. I would say a very worth budget proc to o/c.

Thank's bro, nasib baik saja dapat ini.....
but as i know , Celeron E3200 performance is better than E21XX.....any user if looking for budget proc, Celeron E3200 is first choise....

hi kimtee, i also achive 4ghz, but only at 1.5v

ur proc is good can achive 4ghz with below 1.4v

im using giga ep p43 ud3l



This post has been edited by izzizahari: Dec 2 2009, 09:31 PM

Congra, bro, may be setting problem , try adjust again, i think you also can.....

Can rach to 4Ghz, nice mah...

Good Luck bro.....

This post has been edited by kimtee: Dec 5 2009, 12:01 AM

just some update....

the highest FSB i can boot to windows is 380mhz with x10 multiplier. however not stable to run any stress test.

could be stable if up a bit the Vcore but bit afaid (after some incident, hehe )

but now im using stably at 355x10 24/7. quite good for a chep proc eh?

will run more test, hehe





This post has been edited by izzizahari: Dec 13 2009, 02:29 PM

Ha...ha...bro, you do the good job.......

For me.....4.02Ghz is stable to normal working........cukup dah...tu.....

wah, u got 4ghz stable for normal working? i got 4 ghz also, but the volt still high, scared to use 24/7, hehe

If scared high volt, upgrade CPU cooler

I can do 3.6G stable with stock volt @ 300*12 VID1.2875 (with C1E and speedstep enable)

but whenever I try to increase it fail me on prime95 regardless what voltage i adjusted on :-
- vcore
- NB
- VTT
- PLL
- GTL

can someone give me advise. My target is 4.0G

This post has been edited by k3et: Dec 15 2009, 02:48 AM

so now that's d proven facts we all need to know .
the difference with higher end proc mainly the FSB wall .
damn damn !
could have been nice if at least could reach 400FSB .

usually can run 5-6 years as well...but 1 year n half or below than that i thought the proc can work now after OCing..haha