Read the reply I made just now....P1 acting up...accidently hit 'post' button just now...

Where can burn wan...


Ur ram rated how much???

Ur CPU/NB set how much and how much voltage?? (refer above)

600 too high??????????

kasi baca ini sket : ----> http://www.xtremesystems.org/forums/showthread.php?t=208542
http://ddr2-1508.gigabyte.com.tw/
http://ddr2-1508.gigabyte.com.tw/


600 is considered 'slow' worrrr

This post has been edited by antonio: Aug 21 2009, 04:14 AM

Ok...

I assume these settings is your PC k....

CPU Multi : 14x
CPU VID : 1.4v
Mem VDIMM 1.9v
CPU/NB : 1.1v
HTT: 1.2v
NB : 1.3v
SB : 1.2v

Ram : DDR800
Ram Timing : 5-5-5-12@DDR800
HT Multi : 1800Mhz
CPU/NB : 1800
HTT : 200
PCIE : 100

With the above: THERE IS ALMOST 0.000000000000000000000000000001% that you are going to be unstable.....

So lets overclock:

CPU Multi : 12x (Drop to ensure CPU Final frequency isn't too high)
CPU VID : 1.4v (Bumped voltage value)
Mem VDIMM 1.9v (+0.1v, dun worry about overvoltage with that amount of increment)
CPU/NB : 1.1v (since your just around 2040 frequency, you can leave it to 1.1v, unless you want to go 2400 and above, u need to bump around 0.1v or 0.2v to make it stable)
HTT: 1.2v (more than 225, just bump 0.1v making a total of 1.3v)
NB : 1.3v (usually doesnt make any diff, so leave it)
SB : 1.2v (again doesn't really have any effect, so leave it stock and save electricity (green green green))

Ram : DDR667 (from 800 drop to 667 multiplier
Ram Timing : 5-5-5-12@DDR667 (5-5-5-12@DDR727) 727 will be the speed after HTT 220...
HT Multi : 2040Mhz (when 220 HTT)
CPU/NB Frequency: 2040Mhz (when 220 HTT)
HTT : 220
PCIE : 100



This post has been edited by antonio: Aug 21 2009, 04:58 AM

Stepping/Batch/Production Group...

Lets say in one batch of processors, the output volume is 10,000 CPUs, lets say it takes 4 weeks to produce and pack it all up, so u will have;

0922 APMW
0923 APMW
0924 APMW
0925 APMW

But when there is another 2 or 3 machine which can fabricate and produce them silicones at one time, then it would just put there;

APMW - form machine A
BPMW - from machine B
CPMW - from machine C

tada!!!!

Simple...To avoid any instability due to high CPU clock speed

Either instability due to high clock or not enough voltage...

U use hybrid or sideport only????

Or you don't have sideport at all??

Have u tried without using UMA???

I penah kena, but forget what caused it jap jap...think think

NO!

UMA is the option to curik ur Ram memory....

Disable it will completely cut off any ram curik which forces the IGP (HD3300) to use only the sideport ram (DDR2 or DDR3)

If want to go for high HTT or clockspeed, try not to use UMA....if u don't want to shoot sky high and u have 4GB ram and a 32bit OS, u can ensure that the undetected 500mb or so from ur ram will be utilize handsomely....so no rugi lorr....

This post has been edited by antonio: Aug 21 2009, 03:02 PM

U disable everything or just the UMA?? I mean in the option to select the combination you should select only the Sideport

Dun select;
DISABLE
UMA
UMA+SIDEPORT

Juz select Sideport....

Huh??? Board ape nie???

Try go to through bios see each and every options...

scrap that...check the user manual....

Should be an 'option' not to use the UMA but only sideport...

Unless ur board dun have sideport!!!

Got sideport ahh ur board??? If got surely there is option to choose what speed u want the sideport rams to run at (800,1066,1333) and voltage control (1.8v-2.0v)

owhh...ok ok...

me want to sleep oso....from 12am yesterday till now no sleep...brain already working slowly

owhhh...now want to play high HTT results ehh....

nanti nanti....kasi tido dulu....lepas bukak puasa will play HTT settings

Hehehehe...give it a try see whats what....Setting cara Intel??? OC intel got cara meh???



Me too...


Not interesting??? in terms of what?? final clockspeed??? memory bandwidth, 3dmarko!??

Better u put 667 divider and use 5-6-6-16-22 2T...pump to 1.9v..or better yet 2.0v....

If D3, then u bump +0.1v see if you can boot or not...

Because, THEORATICALLY, if ur ram is rated for 800mhz, then it should work even at speed below the rated...

press control key and F1 key when u already in the Bios....

Will display hidden bios options which is a norm for Gigabyte..

where got master larr, juz happenz to be playing with various brands of boards when hardcore lastime...

nowadays, RM400 sudahh kira mahalll worrr....last time one month buy 2-3k worth of motherboards...

where got kaya....

All credit card saja...now, still in debt

Nope...settle for this only...


Corrupt windows maybe...


Nope...not me....

Low nanti leher-botol the CPU to ram speed...thats is why we neeeeed high speed Memomry Controller Bus....very big and fast bus....

370 kenot lar...divider wont work on the rams...no post if use 667, only 800 or 1066 can use...

Do Ghost....easier next time u windows corrupt!!!

This post has been edited by antonio: Aug 23 2009, 03:41 AM

Shut off or restarted???

If suddenly shut off, make sure PSU enough power and turn off all power saving essentials....since ur in OC mode, no point on CnQ, C1E, PWTRP, DPS, EPU, ALS, FRO, QQA, UFN, and so on....

Also check out ur thermal protection threshold....maybe set to low...


I also kena last week...

Did like u say still 16x....

Last2,

-Flash bios
-Restart
-Shut down
-Power cord take out
-Drain PSU power by pressing power-on button
-Reset CMOS (jumper)
-Take out battery
-take out GFX
-take out dummy card on the 8x slot
-Leave for 1 hour
-Went to check out latest hardware at Lowyat
-Came home, assemble back everything except GFX
-Booted using onboard..
-Go into windows
-Play Children of Bodom - Everytime I die
-Shut down
-Install GFX card back and Dummy card
-Booted into windows and Voila!!!!

-8x mode is enabled!!! yeahhhhh

-But i know u dont want 8x, u want 16x right???

-Reboot, go into bios, set at the first option "Advertised RC", disable UMA

-Log into windows and see if u get 16x.....