what cooler u use?

im currently on 3.5ghz @1.39v, i'll try to get the full load temp..

This post has been edited by pikacu: Mar 9 2009, 07:15 PM

I tried tested in 3.5Ghz @ 1.4V unstable in PRIME95 test

but push up to 3.6Ghz @ 1.45V can pass PRIME95 burn in 24Hour

but temp in 1.45V is very highest

Cooler is Cooler Master Z-600 Black Label. The Z-600BL cooler efficiency like same that stock cooler

bro, remove ya ram cooler, put d fan as push config instead. hope it helps.

This post has been edited by ah_khoo: Mar 9 2009, 08:15 PM

Yeahhh,its true bro ah_khoo...

Hujan sedap OC nie...ekekeke...

lightning strike br tau . deepcool nb8 rm45 kat robyn.. sambar2

booooom lan port nanti asap keluar

owh.. i call it small coz look it as 1s lolz.. but really la.. actually that was a nice result to see... js wonder like thy do NB 3.6GHz on FXB mayb can improve few more s but that need extreme cooling on it.. as i really itchi to try this out last time, but dun hv Deneb on gathering + dun hv the suitable kits to put at NB for extreme cooling...

bro u sure u oeldi activ ur CnQ? aft u enabled it, u still need activ it by going to control panel> power scheme> minimal power management, whn it run in CnQ, it will auto underclock ur cpu speed, for my case 1GHz is the idle clock..

yaya... u make ur coolice setting as push-pull, pretty sure u can feel the improvement in ur cpu temp
try it out bro..
as my cheapo IceBlade if run push-pull oso will show me a nice result thou..

change of multi will disable c&q for some boards iirc...

This post has been edited by ah_khoo: Mar 9 2009, 09:02 PM

Many could unlock the fourth core Of phenom II X3 processor. It was considered that the activation of the fourth core was possible only on processors, released on the fourth week 2009, but recently processors released in 2008 could also unlock their fourth cores. Naturally, not all processors can unlock the fourth core , and even if unlocked not all can preserve stability .

Today appeared a new interesting experiment on how to activate 6MB cache in the third level for the phenom II X4 810 (2.6 GHz) processor, which regularly must have only four mega-byte of cache in the third level.

The motherboard ASRock AOD790GX/128M with the 1.40 bios version for this processor unexpectedly showed the presence of 6 MB cache instead of regular 4 MB. The presence of 6 MB cache was also noted in the system performance.






The author of experiment, failed in revealing the contributing factor for the additional cache volume , but after resetting the CMOS , the processor returned to the standard characteristics with four MB cache in the third level.

I have try Push n Pull configure before , but still nothing

I sure switch into Minimal power managerment, my idle clock in 960MHz @ 1.1V, temp is 35C

ic... in this case, push-pull config may help u..
or u remount ur z600.

how u put ur TIM, iinm this cooler is not HDT tech rite? so the endless of the base is flat 1,
so if posible u make ur TIM apply as thin+flat as possible. that will do better on non-HDT HSF

and the air ventilation in ur casing is vy important..

Bro, i tried 3600Ghz @1.44~1.46v, full load temp is around 56~59 on air (stress using Prime95 blend test)

What!?
Even Cache is unlockable ~.~
What a suprising..

I remount Z600 3 time already but still the same

maybe is my casing air ventilation problem

the stock Cooler Master fan is very very weak so I change casing fan to increase air ventilation

did u recommend a.c.ryan fan？The air flow will be high or not?

P.S: wat is TIM means?

OO, sama-sama

why AMD OC Team can use Cooler Master Z-600 hit to 3.9Ghz @ 1.5V? very confuse

This post has been edited by idragon: Mar 9 2009, 10:34 PM

hint : sponsor + publisiti

gais, need help on chosing mobo to pair up with phenom x3 720.. buy budget is kinda limited, around rm1000 for both proc n mobo =(

w/ proper bios it's doable.

their was handpicked while yas is not bro.

@ noobianz,

i vote for biostar 790gx 128m or even d gx3.

TIM is thermal paste.. do u apply thermal paste? how u apply it? u put it a lot, a lil bit?
u can js check it out by click the link at my sig, air cooling diz thread, there will hv some guide on applying thermal paste..

and the CM silent fan max RPM/CMF is too low.. so it will be hlep if u replace it with a higher RPM/CMF fan..
make it push-pull config(double fan) will help a lot..

720BE around 550Rm
MOBO around 450Rm mayb can get a BIOSTAR TA790GX3 A2+ , JW 790GX EMTREME

else try to funding and topup to get a MSI Platinum series/ DFI

edit:
and i not sure with the OCibility of SB600 on AM3 chip, if AM2+ chip the SB750 will do better..
if there is no prob with SB600, mayb MSI K9A2 Platinum can be in the list, it will cheaper thn the MSI DKA790GX platinum

This post has been edited by cdlim87: Mar 9 2009, 11:27 PM

those who buyin x3 720 are gamblin to get d extra core. in order to have higher chances of winnin d bet, one must buy a proven board. i wouldn't recommend j&w for sure, while there are many successful stories w/ biostar 790gx boards. even dfi can't guarantee 100% success, i'm d best example.

ah_khoo, wut is ur 720 highest oc ? i think i can't get into the 4Ghz with air