anyone with dual channel problem?where e8400 cannot oc wif dual channel mode...but single channel can?

having some problem here with my motherboard
previously when i got it i use my friends E2160 1.8 oc to 3.0 and the board work find
and then alone came my E8600. change the OC setting to auto (default no OC) restart... then shut down.... install my E8600 hit power....
everything power on but the but wont post... there is no showing of any number on the motherboard. it's just.. blank...... then after a while... it boot!!
confuse as i am... everything run just fine... then i shut down the PC
then try power on... same thing happen
blank.. no post wad so ever.... then power off... wait a minute.. power on... only it boot....
anybody can tell me what is the problem here? i even try removing the motherboard battery for a while and install it back... same problem......
so... guys... help me pls~~

eh what u think all the result in most of this thread is.. of course dual channel..

clear ure cmos...
lookup in ure mobo manual on how to do it..

so far what i had tried... clear CMOS.. the jumper changing thing (yes.. did a lot of time last time when i wont boot i clear once..) no help
reflashing bios (just done it.. no help.. and my OC settings are gone.. which my friend did for me.. now i have no idea no OC back...) no help
removing everything and reinstall back the hardware one by one... still no help..
so.... any more suggestion?

Request: since i flash bios and my OC settings are gone.. i was hoping sifu here can gimme some setting that i can try on...
i still got my screanie of my tpower but i dunno what to enable and what to disable..
i am running on E8600, 4gb corsair XMS2 DHX DDR2-800 4-4-4-12 2.1v ram, coolermaster real power pro 750w PSU, 4870 GC...
previously OCed to 4ghz 500X8

edit: previous settings pic


PS: Ocing now is a pain in the ass coz as u apply OC and the system shut off.. i have manually power off and wait for about a minute then power ONLY the motherboard will post... then actually see the OC success or fail... if fail... there goes... 3 retries... 3 minutes of manual power off and wait and power on..... pengsan.....


This post has been edited by hahn87: Nov 11 2008, 01:40 AM

@cstkl1

lol...bro..i m juz asking whether got prob in using dual channel or not..not asking whether can run or not..juz asking whether any prob faced?

bro sean ..most people here post their result use dual channel one..
so no problem loh..

in your case

if on default speed can run then it must be a problem with your setting after oc

maybe d slot itself got faulty...
try swap d rams...and test each one...

lol...i m fine with it...i m helping my friend to ask here...tats all..i m oso using dual channel setting to oc...i havent met him yet..so wudnt noe wats the prob...will go back hometown and c

This post has been edited by teamloks: Nov 16 2008, 05:42 PM

I'm using biostar tpower...with deepcool killer whale cooler..can my ram fit with corsair ram cooler??

can somebody answer my question please......
my motherboard problem is when i shut it down and i need to need to wait for a long time b4 i can turn it on again... if i just power on right away after shut down... the motherboard wont post at all.. the number LED on the board wont show anything.
this is very troublesome for me to overclock my PC since every change of settings shuts it off and turn on again... everytime i have to manually turn off the power and wait for a certain amount of time b4 i can power it back on in order for it to post.....
should i send my board back for RMA or not
tried clear cmos.. tried reflash bios... same problem...
it was ok previously when i was using E2160.
it happens after i swap to E8600.
(i did forgot to plug in the 8pin atx power once and the mobo would on but wont post.. then i realize and plug back in. could this cause my mobo to gone mad?)

my board need to wait about 2 sec and after press power button then will run >.> but nothing happen to me at all

but mine wont post at all =.=..... if good then around 15 second i can power on again... if bad... more than 1 minute.....

>.> no idea

argghh...i nid new bios...come on biostar...make new and better bios...rofl..

haha why bro gonna oc more high ah?

so does it conclude i need to RMA my board?

nolar..bored wif the original bios picture unlike all tforce series that had their renewal of the image...2ndly, yup...wanan try oc more wif more flexible bios

i tink ur case...u check ur bios setup..look at the o.n.e part..make sure its default...u mentioned about 8-pin...did u plug in 4 pin but did not plug in the other one? but i guess if u did not plug in the 8pin, it wouldnt cause d board mad, i had this experience...but not the shut down and on thgy

hahaha board also can mad la like u dont give him full food

@seanlimys
i said already.. OC and non OC oso same case... i did reflash my bios = everything goes back to default.. clear cmos.. by jumper and by battery remove.... everything default.. still same thing... all power pin is in. 24pin +8 Pin plugged in...