yaler i also considering it now... take 2 kits, then can have 4g 1200mhz
MUAHAHAHAHA~

hello overclockers...got some issue..i dont know what it is..but got error on OCCT(crash code 1).all the volt is ady too high i think..but still got BSOD prob..please


Attached thumbnail(s)

lol..its cheap and has gorgeous heatsink

for an e8400 E0, ur vcore is kinda high...i m using e8200 c0 manage to hit 3.8 wif 1.462vcore for 24/7 usage...i dun think high vcore will make the system unstable....correct me if i m wrong...btw...i tink u can set ur vcore +0.200..its enuf

maybe becoz of ram.. u using 4x1gb?
the timing also maybe tight..

nope..he is using 2X2gb..yea 4-4-4-10 is kinda tight for a 2gb stick ram

how u so sure? i saw 1024 @ slot1 there..
different chip module could be the culprit..

GSkill 4gb kits got price cuts...
join d 10MOQ there...
under karom bulk...

kaka...tat reaper heatsink stylish le

i cant load with that vcore

---

Added on October 30, 2008, 7:20 pmyess..i'm using 4x1gb ram and its team xtreem PC6400 rare batch with 4-4-4-10 timing

This post has been edited by soundaddict: Oct 30 2008, 07:20 PM

how bout u try re-o`c back your cpu but this time try set ram timing to 5-5-5-15 first..when u reach your cpu clock target,only u start tweak ur ram

thanks for ur opinion..will try it...

---

Added on October 31, 2008, 12:49 amfor E8400 E0 user what ur setting for this...???
I'm a about to reach 500++ x 8(24/7)

Clock Gen Configuration
PCIE Frequency Setting :
CPU Clock Skew Control :
(G)MCH Clock Skew Control :
CPU Clock Driving Control :

Voltage Configuration
CPU Core1 GTL Ref Voltage :
CPU Core2 GTL Ref Voltage :
MCH GTL Ref Voltage :
CPU PLL Voltage :


This post has been edited by soundaddict: Oct 31 2008, 01:07 AM

hmm ure setting all is crazy...

Bios
set both cpu gtl to 0.635
leave mch gtl alone
cpu pll to lowest 1.5
nb voltage to 1.2v
fsb termination to 1.2v
leave all the clock skews alone( 500 fsb only right)
disable any form of spectrum.
disable all ure cpu config except for ExeCutable Bits and of Course no Of Cores.
set ure dram config to 3
set ure mem voltage to 2.2v for now..
set ure mem timings to 5-5-5-15...
Leave the subtimings alone.

vcore around 1.25v

ok here is how to test ure each component..


OS Condition
theres 4 test i need to pass before running linpack.. ( usually guarantees linpack 64 around 99% chance of passing 50 runs)
this will take a total time of 3 hours or so..

all must be run in diagnostic mode in windows with virtual mem disabled so that u can test ure hardware fully.

disable screensaver
set ure power options to performance and set ure turn off the display to Never

1st Test
Vcore..MAX |VTT Med |GTL ,NB,RAM Lightly
Run Orthos
Set Test to Blend
and Then Set To Custom
Now u can See the Blend Setting
Change Min FFT to 8 Max FFT to 8 Press OK
Start...
U MUST PASS to atleast 35 mins at Priority 10.
That means two rounds of 15 mins and 3rd Round Test 2
so keep upping ure vcore until u dont see any difference or u pass this requirement

2nd Test
FSB - max |Ram, NB - Mid | GTL/Vcore -Low
Same as Above
But Change Min FFT to 4096 Max FFT to 4096
Then start at Priority 10
U Must pass atleast 32-33mins roughly which means two rounds of 15 mins and entering third round Test 2...
For p45.. Maintain Fsb termination One level Above NB VOltage.
Keep upping NB and FSB one voltage higher than NB till u PASS THIS.

3rd test
GTL - MAX |FSB - MAX |PLL - Max | The Rest - Mid
Run Orthos
Set To Blend
And then to Custom
Change only Time to run each FFT to 1 min...

U need to pass all the fft which is from 8 to the last one that is 4096..
stop after 4096 when it enters back to square one at 1024
FOr this mobo.. theres no setting to change for this for duallies.

4th Test
NB/MEM- Super Max | The Rest - Low
Then run memtest windows...
if ure running 4gb run two instances of memtest each at 1700
make sure u pass 100%
Up Vdimm until u pass. or NB tweaking ( u will know when theres no affect to Vdimm increase when for example that 1 error is always there at a certain level.. balance it and get the optimum)


Now u can pass prime95, Linpack and anything ure heart desire for whatever hours ...

Condition
All this assuming ure ram/nb/cpu is having sufficient cooling
Good air flow
Good stable voltages on ure psu


Have fun.
The Rest Google...or asked those ordained overclocking guru in this thread to help ya.

heck this should be a noob guide for p45's

This post has been edited by cstkl1: Oct 31 2008, 02:09 AM

i'm noob...

---

Added on October 31, 2008, 1:48 amthanks man..


This post has been edited by soundaddict: Oct 31 2008, 01:48 AM

lol..nice guide for me too..i m still a noob...learning

well, he is d one and oni cstkl1....
halp others in d most sarcastic friendliest way...hehe

oh yeah dude after u pass all this u can start tweaking ure rams and testing lower voltages for each component until its perfect...

use the above 4 test to test and end it with linpack 5 runs for 4gb...

PS if ure max temp is already over the wall on orthos around 60C + on load ....dont bother running linpack..
orthos priority 10.. is already a hard requirement to pass..

i started to like u man..

hmm i do orthos priority 8 for 1 hour and then linpack 20 loops for stability.. im running 500x9 4.5ghz 4gb ram.. my 2gb crucial tracers+ 2gb team xtreem... lol

post dude..

wheres the post
seeing yat post 4.5ghz stable.. yet no screenies..

infact posting the first 3 test above.. can guarantee linpack stable..
so no need 20 runs of linpack 64 on ure case which will take about one hour 15-20 mins..


This post has been edited by cstkl1: Oct 31 2008, 07:02 PM

yeah dude..post ur screenies..