@raymond5105
sorry for the bad news bro .. my condolence to u and ur family ...

@kabukiawie
5% boost more than dual channel aaa ... hmm.. i'll see what i can do ... hope can still run dual channel again ..

wah.... still can't decide which psu want to buy aaa? hehe ... so hard to make decision aa?

just narrow down ur choice to 2 item only la ... i'll choose either ST50F or CMiGreen 500W ... the CM Real Power 550W can put aside ... hehe ... now u can choose a little bit easier ...

yeah .. that iGreen 500W already sleeved .. so it's look more nicer .. there u go .. the decison oredi made .. so don't have to pening2 kepala lagi ...

---

Added on September 24, 2007, 3:16 pm* it's RM380 aaa ... how bout the ST50F?


This post has been edited by sang_karim: Sep 24 2007, 03:17 PM

dunno how to tell la .. i bought that psu coz wanna oc ... i've always check the 12V rails through cpuz or asus probe and it's never goes lower than 12V at the moment ... so need to utilize the true power psu for my oc lesson

like i told kabu b4 ... dunno how to describe la .. i just use low end gc and pc parts ... dunno how this ST400 psu works very well with that ... only buy that psu for oc lesson ... btw fylon .. have u check this thread ... ST50F at RM 299 ... plus postage i think only cost RM 20 .... can save a little ...

the vcore i think is ok la coz it's only flunctuate between 12V to 12.4+V ... it's what i notice for now ... that not on full load ... will try check it for u guys in full load later ...

wah ... 2-3 weeks eta .. pity u fylon .. if that Lowyat Plaza is in my place .. i'll go and buy the psu u wanted ... pity u ... hope that CM 450W quite enough to power up ur precious stuff inside ...

guys..some update ... here my cpu oc result ... i still don't run stability test yet ... maybe my cpu hit the wall oredi ...

FSB = 250MHz ... running at 3.75GHz and Vcore set to 1.45V ... don't dare to up the vcore anymore ...


Here the 1M superpi result ...


after this i should test for ram oc according to guide given by overclockalbert ... or should run stability test first ti find the stability setting for cpu oc?

i only have sp2004 ... will it be ok? do i have to open 2xsp2004 or just one only?? err...how bout the ram oc? have to do it first or just try with 3:2 ratio??

oredi download orthos and try running it at 250FSB but windows kindda stuck within1 minute .. then lower the fsb to 249 and still the same .. lastly set it at 245FSB and running it till 22 minutes with no problem ... stop it to post it here... .. full load temp bout 49C and idle around 38-39C .. seems ok to me ... will try the 3:2 ratio later ...

@kabukiawie
1.475 still ok aaa? hehe ... will try it later la bro .. wanna try that 3:2 divider first ...

some update ... hehe .. superpi much faster using 3 3 3 8 setting ..



@overclockalbert
still don't run prime test yet ... maybe will try tomorrow la ... sleepy oredi ... need to bangun sahur later early in the morning ... cooling just using Thermalright SI120 as siggy ... oredi close side panel ... hehe ... 2 x 80mm fan at rear for exhaust , 1 x 80mm intake fan at side panel, another 80mm intake fan at front and open 1 bay cdrom cover for air to come in ... no air cond here ... oredi set vcore at 1.475v and will try priming for stability tomorrow ... hehe ... really satisfy with tonite job and thank to ur guys for ur guide ... next job is to find the sweet spot for my rig .. hehe ...

hehe .. 2.5-3-3-8 aa ... will try it toningt and try running prime95 first for stability test ... my kvr only with psc chipset and i think my oc won't go this high with 1:1 divider ... will try with 1:1 divider to look for highest ram oc ... hehe ... now i know how much fun doing this oc ...

so 2.5-3-3-6 is better than 2.5-3-3-8 aaa bro?? i don't really know bout this ram timing la ...

hehe .. so tighter timing to get high ram speed ... will try with that 2.5-3-3-8 first ... if won't work .. will be happy with that 3-3-3-8 setting .. it's only valueram not the high performance one ...

thanks bro ... maybe u can look at post #706 where my superpi improve a bit with 3-3-3-8 timing at 38.969s

owh...so our P4 prefer loosen timing that tight timing aaa?? but tight timing give faster ram speed rite?? why do we need loosen timing .. can someone explain to me?

owh..like that ... tight timing will limit the ram to reach higher fsb ... so if wanna test for super pi better choose tight timing and if wanna go for higher fsb with 1:1 divider must go for loosen timing ... well, i'm learning something today bout tweaking ram ... hehe ... tq bro ..

yeah...i think i'll go find the highest speed for my cpu first ... .. after that will try to get the sweet spot and run prime95 for stability ... still much work to do ...

no la ... don't say like that ... i'm nothing compare to him ... ... just wanna know the highest speed my cpu can goes g4 hitting the wall ... who knows it can reach 4GHz ....