well, 1.95v and 2.0v isnt too far
but yes, i managed to passed SuperPI 1M with that speed..didnt try 32M as it will just wasting my time..

Or if u wanna save a couple bucks, get the Normal KVR with Hynix FP-Y5. I've tested them and max OC are :

2.1V, DDR2 1034 5-6-6-12
2.2V, DDR2 1062 5-6-6-12

wow... tat's not saving juz a few bux... tat's half the buck we pay for a HyperX...

personal tests as well

patriot value rams @ rm130 1gb each at ALL IT sect 14 last saturday
Hynix fpy5 rev C Batch 714AA 1gb x2 with same part number can do ddr 938 5-6-6-18 at stock Volts(1.8v) but apparently rev b can do 5-5-5-15 1t at same speeds...or else u can try to find in LYP for mushkin value rams, with d9 chips of course =)

This post has been edited by bryanyeo87: Aug 21 2007, 02:42 AM

err... i don think Mushkin Value RAMs got D9... at least tat's wat Mushkin told me... it seems tat EM high performance series and above are all D9...

Last weekend I bought 2x 1GB of Kingston Value Ram DDR2-800s (without heatspreader). I forgot to check the chips for details before I stuck on some cheap heatspreaders. But I got them to 900 at stock voltage and timings (5-5-5-15)

System was a E6550 @3.15GHz (7x450) stock voltage on IP-35 mobo.

Hadn't downloaded Orthos yet to do a stability test, but I ran a 10-hour overnight MPEG encoding batch job which maxed out the 2 cores. So I think it's stable enough.

Didn't expect the RAM to go so easily to 900 (wasn't originally planning to OC, so I decided not to splurge on RAM), so will be trying for more in the coming days.

This post has been edited by Traveler: Aug 21 2007, 12:04 PM

1GB kingston RAMs are all either Hynix or Samsung... no need to check... but dunno which chipset model number la... and 900 is 2 low for u...

This post has been edited by t3chn0m4nc3r: Aug 21 2007, 11:28 PM

no wor...got elpida chips ade, then got kingston stamped chips as well for 1gb sticks leh

those are quite rare... the Kingston 1GB RAMs i got are mostly either Hynix or Samsung... now no more d... now Mushkin pulak...

Did u open the heat spreader? DId it really show original manufacturer of the ram ship? I though it will rebranded as Patriot.

It seem HyperX is not really value for money. Plus I read some got problem at DDR800, where it is default at DDR667

I wish my memory has heat spreader, even thought I do not overclock a lot...

So.. How about the Corsair XMS2 DDR800 5-5-5-12 2GB Kit? It should be better buy then the Kinston, right?

a little update on it, ddr900mhz 5-5-5-15 1t possible @ 1.8v

there are no heat spreaders on this la, i didnt put the one with the elchepo ram spreaders, will post the pic up along with my vmod guide for a gfx card 2moro, coz i dunno where my digicam went to

wow...

lots of ram r programmed to be detected below the standard juz to make sure mobo can boot them correctly n let the user to adjust it... most ddr1066 n above r programmed at ddr800 or 667 too... the corsair xms2 is worst than kingston hyper-x... i used both of them before... kingston hyper-x is using infineon chipset... i can't even get the xms2 to run at 800mhz 4-4-4-12 or even 15 at 2.1v... it can barely reach 920mhz on my xms2 at 2.2v 5-5-5-15... maybe i'm bad luck or what... nowadays, lotsa chipset can reach 1000mhz easily n stable.. promos, infineon, elpida, hynix just to name a few...

Wah... Sure or not?

Aiya... What a late reply. I just bought 4 sticks of 1GB XMS2 yesterday...

Anyway, I yet to have time to assemble my new system.

xms2 has a ddr800 cl4 version if i'm not wrong... but anyway, u might have a different luck... hopefully...

Actually I am ok if I only let me run at 400Mhz, where I can already overclock my C2D into 2.8GHz at 1:1 without any voltage adjustment.

Well, maybe I will overclock the RAM a bit... just to round up the C2D figure into 3.0GHz...

yeah... most probably diff luck... cuz i still can't get Mushkin XP series...
this is wat i got... will try lower latency 2nite...

same here...

This post has been edited by t3chn0m4nc3r: Aug 29 2007, 08:06 PM

Since it is XMS why not push it a bit more than 3GHz for ur CPU..

Hmmm.. Yet to able to test my new gaming rig... Now what it lacking is the PSU....

Do you think I need 600W+ to push the RAM? Or 400W will do?

FYI, I have a 8800GTS 320MB