open a hole at rear panel... this is for psu de...





open another hole again at bottom part... to let psu & hardisk can go inside & also for the cable of psu can go through to mother board, cd rom which located at bottom part (another case)....







i take off the hardisk holder from my original case...





then put the hardish holder inside my small case, ketet by screw.... actually the height of the holder & small case is the same...



place the small case at the top of my original case, try n c the case fit o not....

You are one crazy modder you know that?

No crazy mode there is no meaning to mod men......

of course it is still up to individual preference....

seriously... i like his work.. he keeps his worklog updates coming..he got the spirit of modding..

Will the PSU short circuit if you put it somewhere outside the casing like you did? just asking.....

hahahaaa.... cos i am a crazy guy





y u say no meaning to mod? u know y i wan do like that?





kekekkekeeee.... thank you, cos i also wish can finish faster ma





i think no problem lo, but not sure also. who can tell me the comfirm answer???

Wow... very interesting mod you have there... keep it up mates... wanna see the end product

i also hope can go faster, but still got many thing haven do yet.... beside this, i still wan to work every day, haizzz.......

if due to works...
u can start modding on 12.01 am

that thing looks like Aluminium sheet it should be .dont u think it wont be that rigid if you use that

You are very creative. Hope to see the final product soon.

haha, like that tomorro working sure very sleepy lo...





that is white metal (dont know actual name)... if just for psu & hardisk should be no problem... it is quite enough rigid if just put on the top of my case... if put bellow my case sure hapis la, hahahaaaaa.........





thanks..... i will try finish ASAP....

when u put on top of ur case i suggest u put some rubber filings between the top case and the bottom , later sure encounter vibration sounds and groaaa sound ,

ok la, thanks ya suggestion... after it i try to do like that c got what different betwen put o dont put the rubber.... tell u the result later, thanks!

i am not sure what u up to but that's the spirit and enjoyment of modding ...

if i would to know what u will be up to... there is no point of reading through the work log...

keep up and show us what u really have in mind....

haha... ok... the blue rectangle i draw is for hardisk holder before, i take out already....

1st, do u feel the hardware inside my case so tight & too small?? so the air flow very bad in my case, the temperature will increase if after few hours.... my processor is place at the back of the psu, its quite near, just 3cm between only... so every time my processor also very hot....

2nd, if i make a window at side panel sure have to remove my psu & hardisk right... cos they will block the view inside....

so i have to remove the 2 thing then make a small case to place them....






This post has been edited by j@y !!!: Jan 8 2007, 11:51 PM

Basically with ur current rig based on the signature ..definitely ur rig would over heat after few hours .... it just so cramp and the air flow is weak and restricted ...

more updated today....

i cut 1 piece of arcylic to make the front panel for my small case.... i wan pasang two 80mm fan at front panel....









cut 2 blow hole there to have a good air flow in the small case, especially for my hardisk that place at the back of the front panel.... the psu also in the small case so if dont have a good air flow sure will very hot inside....











then drill some hole for the fan screw & case screw....









gosok again the side, will more smooth after doing it....









it is the look after i tight with screw already....

nice job ... u should proud with what u did so far.... i have never gone this far for a case....

with the two fans ... ur HDD should be safe ...

keep up ...

that signature is my latest comp, this is old 1....

u r right, it is so cramp and the air flow is so weak and restricted...but it will not over heat...

haahhahaaa... i wan put 2 HDD there, if no fan my HDD sure will get heatstroke...