i am using NH U-12F

Can anyone here post their CPU temp after using Noctua?

My Noctua fan show 800RPM without the ULTA cable connect? Should't it be 1200RPM?

The best Push-Pull effect is to have a wind tunnel effect. A higher pressure CFM fan should be located at the Pull (Rear) side. In short, the difference in air pressure movement will create Vacumn Pulling like effect to expel the hot air to the back case fan. In general, that's to say :

Pressure:  (case rear fan) > (pull fan) > (push fan).

Then it will create a gradual pulling air movement effect.

If you are having a rear 12cm case fan,and you intend to use a single fan configuration,  it should be of a higher pressure than the 1 placed on the HSF. To increase air movement efficiency, a semi closed shroud should be constructed from the rear of the HSF directly to the rear case fan.

Can anyone here post their CPU temp after using Noctua?

My Noctua fan show 800RPM without the ULTA cable connect? Should't it be 1200RPM?

The best Push-Pull effect is to have a wind tunnel effect. A higher pressure CFM fan should be located at the Pull (Rear) side. In short, the difference in air pressure movement will create Vacumn Pulling like effect to expel the hot air to the back case fan. In general, that's to say :

Pressure:  (case rear fan) > (pull fan) > (push fan).

Then it will create a gradual pulling air movement effect.

If you are having a rear 12cm case fan,and you intend to use a single fan configuration,  it should be of a higher pressure than the 1 placed on the HSF. To increase air movement efficiency, a semi closed shroud should be constructed from the rear of the HSF directly to the rear case fan.

You can check out my temp at Air Cooling Thread there...mine running more than 1200rpm, sometime even go up to 1300rpm++ (mostly during hot weather or during load)
ic...so let say I use Noctua NH-S12-1200 (80CFM++ (not sure is this the correct value) as push, FM-121(110CFM) as pull, and then use NMB (like the one in your sig there which have 118CFM) at rear casing there, then it will have gradual pulling air movement effect right?

This morning I reapply the Noctua promotion items as they did not send me any email after I apply last time, to be my suprise, I found an email telling me the items being sent today when I open my Outlook Express after I reach home from work...   nice job Noctua...    

i have good news to share..For those who's still don't know about this promo items.just go to this link

http://www.noctua.at/main.php?show=promo_order&lng=en

this real..i just get the stuff today.Got 1 x Noctua Metal Case Badge and 1x Noctua Sticker Sheet A4(1 very big Noctua logo.it's 3/4 of A4 size, 1 med size, 2 small and 6 very small sticker.the size just like normal branding sticer like comes with mobo, cpu etc )
** i can provide the picture if u don't believe

Bulk ver. 3.0
1. Xanaris (NH-U12F)
2. Polaris (NH-U12F) RM50 DEPOSIT PAID
3. A^boY (NC-U6)
4. irangan (ME ) (NH-U12F & NC-U6)

im getting max 38C priming in blend setting..am2 3000+ in stock..in closed casing setup 

hahaha...finaly irangan oso get one for himself liao...kekekeke gd luck for ur bulk

some average stuff lo.. c2d 6600 and so on....

Can anyone here post their CPU temp after using Noctua?

My Noctua fan show 800RPM without the ULTA cable connect? Should't it be 1200RPM?

hahaha...finaly irangan oso get one for himself liao...kekekeke gd luck

Hi,

As a matter of fact, the Extended Warranty Program has been created for the NH-U12 and NH-U9 coolers which came with a 3 years warranty. The NH-U12F already comes with a full 6 years warranty, so there's no real need to join the program. I can also assure you that we treat all warranty issues as obliging as possible, so it's no problem that you've got no invoice.

Best Regards,
Jakob Dellinger

presse@noctua.at
http://www.noctua.at

RASCOM Computerdistribution Ges.m.b.H
Huttengasse 71-75
A-1160 Wien
Austria
http://www.rascom.at
FN 198653n | Handelsgericht Wien

support@noctua.at wrote:
   

-------- Original Message --------
Subject:     Extended warranty program
Date:     Sat, 03 Mar 2007 13:09:21 +0000
From:     My YeeYee <my_yeeyee@hotmail.com>
To:     support@noctua.at



Hi,
I've bought one of your product, NH-U12F CPU-cooler, I would like to join the extended warranty program. But the problem is, I bought your product from a forumer, and I don't have any invoice or receipt on hand. M I still available for the extended warranty program?

Thank you.

Truly,
KT

If not mistaken he already buy in 1st Bulk but not compatible.Ordered this time to give to his ehemm eheemmm 

@irangan
haha, finally ur new rig is in the proccess.
would cost a hole in ur pocket, ur GF nooded already la?

@kataro
correction on fans airflow is not 81cfm, its 81m3/h, abt 47.67cfm.
conversion: 0.58857m3/h=1cfm
____________________________________________________________

For those who wanted to join the extended warranty program, ive jus got this mail from noctua support, best service ive ever encountered.

@kataro
correction on fans airflow is not 81cfm, its 81m3/h, abt 47.67cfm.
conversion: 0.58857m3/h=1cfm

hahaha..hey jeff...it's time to change ur new siggy liao

I emailed the support... hope to get their reply soon...
I am using INTEL QST, maybe this is the cause as well...

If not mistaken he already buy in 1st Bulk but not compatible.Ordered this time to give to his ehemm eheemmm 

@irangan
haha, finally ur new rig is in the proccess.
would cost a hole in ur pocket, ur GF nooded already la?

@kataro
correction on fans airflow is not 81cfm, its 81m3/h, abt 47.67cfm.
conversion: 0.58857m3/h=1cfm
____________________________________________________________

For those who wanted to join the extended warranty program, ive jus got this mail from noctua support, best service ive ever encountered.

coz now he getting new rig liao...

offtopic: who is YeeYee?