Standard SETUP.., Look @ this b4 u plan to setup ICE
|
|
 May 30 2011, 02:05 PM
Return to original view | Post
#41
|
 
Newbie
3 posts Joined: Jan 2009  
|
QUOTE(genpaku @ May 29 2011, 05:33 AM) ok...for now i want to buy comp set only...budget rm600-800...interested with Focal 165A1...izzit good for rock music? yes actually theyre quite ok, not bad for rock music as a beginner model.... |
|
|
|
|
|
Jul 25 2011, 02:04 PM
Return to original view | Post
#42
|
|
Newbie
3 posts Joined: Jan 2009
|
amp 1 will be enuff power (500W@2ohm) for either sub 1 (400W rms) or sub 2 (250W rms each).
go for amp 1 with sub 1 lah..... This post has been edited by zennn: Jul 25 2011, 02:06 PM |
|
|
Jul 26 2011, 12:59 PM
Return to original view | Post
#43
|
|
Newbie
3 posts Joined: Jan 2009
|
QUOTE(krayden @ Jul 25 2011, 04:54 PM) OSB: He stated that the sub is 400w rms, not max. gpt laa.. later he ask about another mtx SVC sub, he wants to use 2 units parallelso it should be each VC 200w rms. Zenn: errr where got sub 2? Added on July 26, 2011, 1:02 pm QUOTE(mfcm @ Jul 26 2011, 02:35 AM) auxdio vs maximo which one btter?or got better model for component set? never heard of auxdio, so id go for morel...This post has been edited by zennn: Jul 26 2011, 01:02 PM |
|
|
Jul 13 2012, 11:34 AM
Return to original view | Post
#44
|
|
Newbie
3 posts Joined: Jan 2009
|
just wire the dual voice coil sub to the monoblock with parallel wiring, the amp output will become double
|
|
|
Jul 17 2012, 01:57 AM
Return to original view | Post
#45
|
|
Newbie
3 posts Joined: Jan 2009
|
install a small 8 inch sub in a small box instead
|
|
|
Aug 30 2012, 01:00 PM
Return to original view | Post
#46
|
|
Newbie
3 posts Joined: Jan 2009
|
yes it is and yes it will. im assuming youre not using the passive xover in your component speakers. also provided the 3 way xover has the correct frequency range for tweeter
|
|
|
|
|
|
Sep 5 2012, 11:45 AM
Return to original view | Post
#47
|
|
Newbie
3 posts Joined: Jan 2009
|
around 2000 hz and above
|
|
|
Sep 10 2012, 10:00 PM
Return to original view | Post
#48
|
|
Newbie
3 posts Joined: Jan 2009
|
if your xover is intended to be used for tweeter then u dont need to put the cap or resistor on the tweeter.
|
|
|
Oct 8 2012, 03:59 PM
Return to original view | Post
#49
|
|
Newbie
3 posts Joined: Jan 2009
|
QUOTE(aeonic @ Sep 13 2012, 12:02 AM) 1. Pioneer AVH-4450BT 2. Alpine SPR-17S - front 3. Alpine SPS-610 - rear - powered by HU 4. Pioneer GM-6500F - bridged to 2 channel to power the SPR17s 5. Alpine SWE-1000 underseat active subwoofer 6. 0GA power cables 7. Caliber CR-5 RCA cables. 8. Dynamat 4 door + trunk - 1 box 9. No brand speaker cables. I have an extra audio control xs4, is it recommended to use the xs4 and make the system to active and take away the spr's crossovers? Will this be a better setup? i also feel u can use 4awg power cable instead of 0awg and use the money saved to get better speaker cables |
|
|
Dec 12 2012, 11:08 AM
Return to original view | Post
#50
|
|
Newbie
3 posts Joined: Jan 2009
|
can lah, ive used that way before on the jazz for competition, its all about trial and error before deciding on a final location, with some compromise of coz
|
| Change to: |  0.0196sec
 0.65
 7 queries
 GZIP Disabled
Time is now: 26th November 2025 - 10:45 AM |
Quote