Good news for DB120-WL user! stren89 make me curious and I start research about Riger DB120-WL hardware used.
This will improve your DB120-WL Ethernet, Wireless and ADSL by using latest driver provided by TP-Link, straight improve DB120-WL efficiency. Click here to see inside Riger DB120-WL!
I have 2 Riger DB120-WL at home, I got extra one because I accept TM upgrade offer last time.

Before proceed, take this precaution.
1. This applicable only Riger DB120-WL (Silver) with Firmware Riger V .4 installed by default.
2. Before proceed updating, please connect your computer directly via LAN Cable to DB120-WL
3. This may void your warranty (maybe not, since you didn't open the case)
4. Doing at your own risk!

If your DB120-WL still have warranty and scare get broken, I suggest you follow, stren89 guide.

Important Change!
You need to accept this awkward changes, because LED driver operate at different signal. You need to learn:


Easy Guide start here:
Read carefully to avoid invalid or mistake during updating

1. Download Firmware
Download TP-LINK TD-W8951ND v5 firmware from TP-Link Websites

2. Extract
Open zip file and then open "TD-W8951ND_V5_140226" folder and extract (simply click once and drag)
[attachmentid=3971330]

3. Login
Note: Do this only when computer connected via LAN Cable (Hardwired)
Username: tmadmin
Password: Adm@**** (**** is the last 4 HEX digit of MAC Address, eg: D1E3 => Adm@D1E3, you can find bottom of your DB120-WL)
[attachmentid=3971328]

4. Click maintenance
After successful login, click maintenance and then click Firmware, until you see this page:
[attachmentid=3971332]

5. Choose firmware
Click New Firmware Location: "Browse" button and then locate back where you extract just now, and then open that folder and choose "ras" file

[attachmentid=3971333]

6. Proceed!
Click "UPGRADE" button! and wait until you see a progress bar!
[attachmentid=3971335]

7. Update complete
Once progress bar reach 100% and it will redirect to new TP-Link login page!
Please login using previous username and password (it's look awkward when login using tmadmin under TP-Link page, lol)
[attachmentid=3971336]

8. Finished!
Well done, now you have working DB120-WL with TP-Link Firmware! TP-Link will use your previous configuration.
[attachmentid=3971337]

Extra: Improve Wireless Backdoor + Device Security
After flashing and login with old password "Adm@XXXX", simply reset to factory default, this will:
1. Remove extra Virtual or Guest Wireless/AP, leaving only one.
2. Using default TP-Link settings, including default username and password (admin, admin)
3. Overall stability!

NO INTERNET AFTER FLASH!?
Follow this guide by ngeseng how to configure Streamyx ADSL VCI/VPI

Here what I done...
[attachmentid=3971339]
[attachmentid=3971341]

TP-Link Firmware
No Light = OK
Constant Light = NOT OK
Blinking = ACTIVITY

need configure VPI/VCI
VPI: 0
VCI: 35

try set WiFi only use 802.11n and 20MHz bandwidth

are you sure? you already reset router to factory setting after flash new TP-Link?
this will remove hidden SSID: Riger1, Riger2, Riger3

use WPA2, AES

check Wireless Id: 1,2,3,4
this riger can make 4 SSID, which 3 is hidden

SSID Index : 2 3 4
Broadcast SSID: NO NO NO
SSID : Riger1 Riger 2 Riger 3

if you reset to fectory, this index will go away...

even Broadcast SSID set to NO, still allow user to connect Riger1 without password

reset factory via page or button?
it should via page...

if index ssid still exist, just password all other 3 ssid...

dont have riger V4
do you do factory reset after flash?

Hi Anime - hope all is well with you. Today my Router DSL light is ON and the Internet light is also ON without blink thus i cant connect to internet. Pls advise what shall i do, thank you.

PLEASE HELP Anime; Anyone !

that modem has multiple PVC, disable all other, leave one enable, and set