mushkin relabelled it edi. no idea is using what chip. How does your ram perform?

Evogenix

yup. tat day i went viewnet, but no stock. So, bought it at cycom.
get ram that got good d9 chipset

same as mine, cant rum stable at 2.4vdimm. You tried increase using divider? You might get higher frequency

Evogenix

i faced a lil problem

i oc-ed my system as in siggy,
dual prime stable for 8 hours, memtest86+ for 6hours, folding 24/7 no errors, but, why everytime i restart my pc, it will auto boot afew times before go into the post screen?

BIOS problem?

Evogenix

arg... faced anather problem again.

any ds3 user here had a RAID0 setup??

I setup my RAID0, and completed windows installation, but everytime I restart/reboot (even with default clock speed), the BIOS cant detect my RAID setup. I have to manually off it, then on back, problem balu solve.

anyone know what happen?

Evogenix

woot, welcome dude.. finally dumped your amd64 edi??

4GHz always waiting for you

Evogenix

This post has been edited by Evogenix: Sep 25 2006, 11:21 PM

my oc-ing result


1.425vcore on xp120

Evogenix

This post has been edited by Evogenix: Sep 26 2006, 09:55 PM

sure...

ds3 setting:
1.425vcore
+0.4vdimm (5-5-5-15 @ 1:1)
+0.1vfsb
Normal PCI-E
+0.1vmch

din watch for the temp, will post the temp the next oc

Evogenix

This post has been edited by Evogenix: Sep 26 2006, 10:14 PM

woot... gratz... 4GHz sia...
just hoping my 6300 able to reach 500fsb

Evogenix

i just remove the n/b heatsink, cleaned the default thermal pad and reapplied with as5. Then, mod the spring fitting abit... too bad, cant see the temp improved. need to search for 40mm fan now.

Evogenix

talking about the reappling as5 on my n/b yesterday, i just did an oc-ing and found out that it improved my oc result from 465x7(3255MHz) to 475x7(3325MHz) with 1.425vcore



gonna prime it for hours now. Hope it stable on this clock speed

Evogenix

prime stable for 1hour+


so, i tried with higher fsb - 480, weird thing happen, it hang. I reduse the fsb to 479, no luck.
Then, i tried 476fsb, guess what, still hang when at the post screen. Incresed vcore from 1.425v to 1.5v, not helping at all. Changed other setting vMCH, vFSB etc, still the same.

I dont think its the voltage problem, so i reduse the vcore to 1.4v, vFSB to +0.1, vMCH to +0.1, and now priming @ 475x7(3325MHz). Stable for 13minutes so far.

If redusing the voltage can stable the speed @ 475fsb, why still it wont go over 475fsb even more voltage applied? Proc limitation?

Wish me luck for not proc limitation

Evogenix

haha... gv you a hint, go search for vr zone 6600gt mod, there is a guide to tighten the spring using nuts i used the same concept on my chipset's heatsink.

edited : where to see the n/b temp anyway? i used core temp to view my core temp.

Evogenix

This post has been edited by Evogenix: Oct 9 2006, 02:57 AM

pc wizard 2006 reported my mainboard temp 34-35 dCelcius full loaded

Evogenix

Miracle happened, now priming @ 480x7(3360MHz). What I did? I just now stop booting until it wont freeze in the BIOS post screen. The success rate is 1/10.



edited : all setting remain the same, except vMCH +0.2

I still not get acually whats the problem. Maybe its the chipset that causing this headache.
Evogenix

This post has been edited by Evogenix: Oct 9 2006, 03:01 PM

but the chipset aint that hot as i read from PC wizard 2006
max 35dCelsius nia...

got other recommaned software to read the chipset temp?

Evogenix

change to water cooling my friend

the PCW06 reading like not v accurate tho "

TAT about 1-2 dCelcius lower than CoreTemp

Evogenix

apa lu cakap ni??
tak paham

Evogenix

increase the fsb until it not stable, then balu add the voltage

SP2004 is used to test your system stability, you jsut need to run it for 24hours. If it dont crash/reboot, means your system can consider stable lor...

For SPI its a benchmarking tool. The lesser second yuo get, the better.

Evogenix

for my case, I increased vFSB -> vMCH -> vCore
vDimm only applied when your ram not stable

Evogenix