after installing noctua cpu cooler... 72C onload down to 58C...



Attached thumbnail(s)

actually fatality's price quoted as the same price as biostar.. that's why asking for good one..
as everybody said biostar is good... but i found fatality layout more nicer.. but the pci only 1... maybe blocked if using sli... it's hard to decide..

biostar nf590
1) 4 sata
2) good oc
3) 2 pci
4) 1 ide
5) simple active cooler
6) blue pcb

abit fatality
1) 6 sata
2) quite ok oc
3) 1 pci
4) 1 ide
5) heatpipe
6) red pcb

try AS5 or CM premium la.. or maybe some polishing..

what ur htt mul? try to set 3x if more than 250fsb..
and maybe vdimm not enough.. that's the only thing limiting the rock stable M2N-E...

don't buy MSI.. go for biostar instead.. make sure it's tforce.. if suit ur budget..

on 200 fsb... divider ddr 667 i set 1.8v..
but on fsb 266 with divider ddr 533.. ram will work on 667.. need 1.9v..
i'm still wondering why...

i can accept if using tight timing require more vdimm... but in both setup i used same timing.. 4-4-4-12-16 1CR..

with the same timing also can use on 220 fsb, 667 divider, v1.8 .. resulting 733..
but 260 fsb.. 533 divider.. resulting 650.. must use v1.9...

is it becoz of htt increased?

---

Added on March 3, 2007, 12:29 pmisn't it 2400/9 = 266
should on ddr 533.. mean normal vdimm should be ok?

This post has been edited by 8tvt: Mar 3 2007, 12:29 PM

show us the screenshot before click the 'ok'.. do for 32m one..

65w and 89w OCbility differ.. especially on voltage needed..

i've tried until 70C edy..
i think 60C refer to core.. sometimes unstable system not caused by temp or reached the wall... but over voltage also...

last time i need 1.55v to set 2.6ghz.. after a few burn-in 1.5v is ok...
right now.. 1.48 also can stable..

it's base on luck.. ur cpu need more burn-in..

just use the orthos also can.. leave it for few hours..

i think for ur case not becoz of the cpu cannot go far.. maybe the ram divider is not right... and htt exceed 1000.. depends on mobo though...
reaching 260fsb i set 3x htt mul...

cpu also need a little training... like motorbike.. always need to full trottle to make it faster... after sometimes it will get use of it...

since when this thread change to basic OC n QnA? i think if we look back the thread we can almost find the answer...

come on.. give some great review..
i'm eager to now how 65w or 35w or even 65nm X2 performe...
no one own it?

ya.. that's weird.. how about the mobo not support 'half multipliers'? can solve with bios update i guess..

but through calculation... can hit 3ghz without much stress on ram if using 400 divider...

320fsb x 9.5cpu mul = 3040

3040/9 = 337... 675DDR...

if 533 ram divider.. much more good for OCable ram..
3040/7 = 434..

this should be great for merely RM300 X2 cpu... prepare ur money guys..

---

Added on March 22, 2007, 11:27 amnormally from ordering number..

89w = ADA3800...
65w = ADO3800...
35w = ADD3800...

This post has been edited by 8tvt: Mar 22 2007, 11:55 AM

obviously it's 89W.. like mine.. if 65W need that high V.. it's totally bad chip..

Biostar TA690G builtin gpu not very good i think.. coz it's cut pixel shader into 4 and remove vertex pipelines.. so will stress a cpu..

is there any AM2+ mobo around?

if not limit the gpu.. and got firewire.. those mobo will be great for basic audio visual platform...
and again got hdmi and dvi connector.. great for the price..

not only stock cooler... stock vcore too...

don't trust the cpu-z reading..

err.. 3x cpu mul?

china made normally require more voltage..
but for sempron 'diffused in singapore'..
i believe 65nm fab in germany..

lol finally u made it..
set 261 la.. RAM CL can set to 4 though..

holy moly.. using stock cooler or noctua.. must grab 1 la like this..