hi anyone, i has been bricked my router.
i am able to enter to failsafe mode by using putty.
but the thing is i can't set passwd due to no space o the device and i not able to use the command firstboot to clean the space?
anyone know how to solve this?

how to bricked it ?

what firmware u flash when u brick it ?

this openwrt-ar71xx-generic-tl-mr3420-v1-jffs2-factory.bin.

Install openwrt huntsman in mr3420 but zte mf190 not detected..anybody???

Why use ROOTer when stock firmware works well?

hi guys, i just bought e3276s-151 with firmware version of 21.260.05.00.00 and pair with tp-link tlmr 3420 firmware v2.4 .

somehow i installed three version of firmware from http://www.ofmodemsandmen.com/downloads.html yet still i failed to connect to internet when the usb dongle modem is plugged into the router.

can all sifu please give me some helps on this ?

i even flashed to the Huntsman 2013-10-12 / LuCI Trunk (svn-r9811) yet still failed to connect .

my usb dongle modem works fine as it can connect to internet when directly plug into my laptop.

on the other hand, can i know how to flash back to stock tp-link stock firmware? i try to flash back from openwrt firmware but failed. and i got this notification - The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform.

I download the tp-link firmware from here.
http://www.tplink.com/fi/support/download/...ersion=V2#tbl_j


i wonder the connection type shown on the usb dongle there - RAR(modem) and NDIS. which one should i use ? or either way works fine ?

Shaney

If you USB modem is Hilink, it won't work properly most of the time.

Try set it to NDIS and try again on rooter.

HiLink default ip is 192.168.1.1, try to change the router's ip to 192.168.0.1

Clash of IP i believe.

Great, someone please test can it power the E3276 / E3272 properly now

hi anybody can help to flash AF23 to support Vodafone K5006-z

blacktubi
Dear networking sifus, need your help.

My main internet is from Huawei E5331 mifi. I have some devices which only have LAN ports. I have a spare TPLink MR3420. Hence I need to do bridging.

E5331 > (Wifi) > MR3420 (LAN cable) > Any devices such as pc/laptop

Can i use this method?
http://www.tp-link.com/en/article/?faqid=74

Please correct me if I'm wrong (based on the link above):
[Part 1] E5331 IP remained at 192.168.1.1 while MR3420 will be 192.168.1.2
[Part 2] On MR3420, enable bridge and enter MAC address of E5331 per tutorial. The tutorial said repeat the steps on another router (E5331). I need to enable bridge on the E5331 too? I haven't check the E5331 setting page yet, and I doubt there's such setting.

Skylinestar I never try this. Maybe you can try it.

MR3420 use WDS bridging which is easier to setup.

But I pretty sure you can do it on OpenWRT.

I think I'll try this:
http://blog.shanemeyers.com/2011/09/24/bri...p-link-routers/

http://www.tp-link.us/article/?faqid=440

This post has been edited by Skylinestar: Dec 25 2014, 11:43 AM

Guys

Need help... I forgot what setting I have done and I can't openwrt huntsman firmware cannot connect to my modem on (TP3420).

What need to be set in interfaces there?


OK. SETTLED

This post has been edited by jack2: Feb 16 2015, 03:47 PM

Tried to bridge my MR3420 (extended router) to the main TM Riger modem router (main router)...failed.

The WDS status on my tplink says Run...but I can't connect to the internet.

Can anyone help?

This post has been edited by Skylinestar: Mar 27 2015, 02:10 PM

Don't use WPS, manually wire them together

My main purpose is to extend the lan/wifi coverage.
My riger is on the 1st floor. I have a spare tplink, which I wanna put on the ground floor living room as extender/repeater. Therefore, I need to use wifi instead of hard-wired.

Still no luck.

Buy a powerline to link the 2 together.

You can always flash to OpenWRT and configure it as a repeater. Google for steps

actually uc an flash rooter http://www.ofmodemsandmen.com/index.html

easier for you to bridgeto your riger