Hi,
My Modem D-Link DSL-2730E gt IPv6 DNS and IP already
DHCPv6 Mode Set to Auto Mode already
Why my compuer IPv6 still is No Internet Access..
Help please..

Have you actually tired restarting both the modem and your computer?

how to check whether support or not
btw this 2 days get frequent dc again

Make sure that you are connected to an IPv6 network then visit a site like test-ipv6.com to test your ipv6 connectivity. Most mobile internet do not have ipv6 yet like my umobile.

Here's my test in chome browser app:


My S2 doesn't show the ipv6 address in the wifi connection details nor the phone status page but that test site shows my ipv6 address and it has full 10/10 v6 connectivity.

Btw, this post is sent from my S2 for extra testing too.

As for your dc issues, do you think it's related to your firmware update?

later I try
but I thought only 1.06 firmware can enable ipv6 while 1.01 can't enable ?

and normally is related to firmware update issue, my phone normally can connect while computer sometime showing ! icon at bottom right hand site (wi-fi signal bar)

Yeah, unfortunately v6 cannot be enabled with 1.01 because the dual wan checkbox is disabled on the web interface, so an upgrade is required to use v6 but I am hesitant to update because of the dc issues you're facing in 1.06.

I'm using my asus rt-n66u running on dd-wrt for v6 by the way. I'm glad that I no longer have to depend on that L7 router and can now use it for testing/development.

Thanks, @asellus for pointing out & @rizvanrp for the step by step guide. Update to routerOS 6.5 and re-configure seems solving my issue.
Finally, managed to visit test-ipv6.com and get 10/10 results.

I was referring to the IPV6 address I get in my Windows clients. Not quite understand DHCPv6 difference that IPv6 address in this case.

This post has been edited by maxiscool: Oct 24 2013, 11:15 PM

Update:- Manage to get IPV6 if using Chrome. Safari doesnt seems to interpret correctly.

How come my post do not have IPV6 indicator as other forumer despite success in test-ipv6.com

This post has been edited by maxiscool: Oct 24 2013, 11:13 PM

no wonder, but the router provided by TM really cannot use
when free also need go buy 1

I'm doing further test on the setup of IPv6 despite having 10/10 result on test-ipv6.com.

I disable the IPv4 interface and left the IPv6 turn on only. (reboot router and windows interface just in case), and i get an IPv6 address.

And when I try to ping www.google.com, it request time out, is this the expected results?

Maxiscool: No. This is not the expected result. It should be able to get reply from google.com with IPv6 address.
What device are you using? PC or Phone?

How to find out your IPv6 really work?

Solution: disable or just make your IPv4 address change to static while simply randomize and input gateway IP.
Leave IPv6 settings auto assign by DHCPv6.
Then try to ping and surf www.google.com
If can surf, that means your IPv6 is ready to be used.

This post has been edited by darrenliew96: Oct 25 2013, 09:31 PM

I just did the same test, disable ipv4 protocol in the interface, and access lowyat forum again, no problem, but I couldn't access most of the sites due to not ipv6 enabled web site

I can see your post in lowyat does have the IPV6 tag, your ipv6 should work.

The IPv6 of lowyat is recently implemented?

Hi Darrenliew96, I'm using a PC. Apparently I've figured out the root cause, it is the DNS not assigned to my device, manually insert in the DNS field on the PC, it works surfing to www.google.com and forum.lowyat.net.

Now, I need to figure how I correct this config, any help?

Try this two google IPv6 DNS

2001:4860:4860::8888
2001:4860:4860::8844


For IPv4
8.8.8.8
8.8.4.4

Thanks, this will work if I manually entered in each client/PC.

But I'm trying to check how come it is not push to each client as the correct DNS without manual input.

You cannot do that if you use Windows PC, the router is routerOS and disabled the IPv4 stack in Windows.

Not quite understand that, but I'm trying in PC and MAC. What you mean is that Windows need manual input? My MAC also need manual input. Is that anything i need to look at ?

Your Mac run what OS X version?

Maverick..