then Im not sure, I dont have this device

Any one able to successfully migrate the VOIP from Thompson to Huawei ?
I jz able to get the IP after changing the VLAN to 822.
And the SIP Server address seems not working ...
What else do i need to change at SIP?
1. SIP ID?
2. Auth name?
3. Reg Server address?
4. SIP Service Domain?

I did. Just follow the instruction from first page...

Really? but my VoIP LED jz remain no light... and the VoIP Regist Status in the HG850a is still unregister.
But i did get the IP for the WAN after change the VLAN from 400 to 822.
Any advice?

Double check whether you follow the steps on page 1.
And also verify the setting is same as thompson router.

Guys, this is really good instruction.

Thank you thankyou and others.

But, in my putty session, i still cant save the configuration. i already use the 'save' command.

i only do the iptv part only. then after reboot my hg850a, it go back to previous setting, not vlan id 600 anymore on LAN port 4.

any tips?

Hi,

Did you manage to save the configuration ? My settings are all gone now and I can't seems to save it.

Have you tried SSH? Most probably its in SSH.

No i dont

i got the same result.. UNREGISTER

any solution?

SIP - 03(my phone no)
Auth Username - 03(my phone no)
password - 03(my phone no)1 <-- is this correct?


above correct?

Help... I have successfully gone thru the telnet, but I can't login to the modem GUI using the username / password provided.

I just switch from TM to Maxis recently, is the password been changed by Maxis? Anyone knows what is the password?

Thanks in advance.

Had this problem before and found out that I got a wrong phone number configured into my original technicolor router. Asked the maxis guy and they give me my correct phone number and password and all is okay. The password can be as you said above or mine is a combination of few numbers which I don't remember much. Just ask them vua twitter, they're quite responsive during work days.

Is there a way to change the GUI password for the HG850a using telnet?

password may not be 03(xxxx)1

I had the same problem, googled hard enough to try another method. Look up your void invoice from maxis for the account number, and plus the last 4 digits of your phone number

Eg: Your Account number: 177889900, and your phone number 03-12345678

your password will be 1177889900(5678) (without the brackets...)

and works for me.

This post has been edited by forum.bear: Jan 28 2014, 05:15 PM

First of all, thanks to the TS for the information, all work beautifully.

Here are further issues that I was facing, and got that resolved, hope the information able to save some of you time.

Phone Always getting engaged dial tone
Another issue if anyone facing the same, is that even i got my number shown as registered, I kept on getting a engaged tone.

To fix that, go to the Advance, VOIP, and click on the associate check box, then click Apply.

Phone kept on disconnecting
If your phone got disconnecting often enough, you can go to Advance, VOIP, SIP Advance, and change the session expired and minimum session expired to 0 (which means, unlimited)

got those information from the HG850a manual
http://www.docin.com/p-545975576.html

in order for the voip led light to show, the username/password needs to be correct.

Username, Auth Username will be your phone number including the area code.

eg: 0312345678

Password will be either:
0312345678 + 1
or
Account number (from your voip invoice) + 5678

once is correct, you should see registered on the front page.

HTH

want to give this user/pass a try? i got this from a online HG850a manual

telecomadmin / admintelecom

Hi Bear,

Thanks for your reply. I already tried that username / password, but it doesn't work for me.

is your HG850a v3? I remember reading some post about there are different version of HG850a. According to the manual, the root / admin will get you in as well, but it might not have enough privileges... once you log in, maybe can dig around and see is there any place you change the things you need.

This post has been edited by forum.bear: Jan 29 2014, 01:07 PM

Hi Syk,

Recently my router is broken, keep show me the yellow light on the power. So I have followed instruction and success set it with my router WRT54G2 but face the problem as you faced.
Do you manage find out any solution to solve the save function which is not working.

Thanks.