Amazing work credit detail , thanks for share

I'm having difficulty getting my Huawei E398 to use qmi instead ppp. I'm not familiar to the whirlpool forum and don't know how to do a search. Have you seen anything tested it successfully? Thanks in advance!

Thanks for trying

Best to join Whirlpool and raise the matter re the Huawei E398 in the 4G Open WRT developers thread.

http://forums.whirlpool.net.au/forum-repli...76&p=-1&#bottom

It's not very formal and just bumbles along until we get someone like you with a new challenge.

Just pop up and say something like"Hi from Malaysia. I cannot get my E398 to run with QMI etc ..."

Cheers

John k

This post has been edited by Wahroonga Farm: Feb 9 2013, 03:20 PM

thanks sifuuu..

hi
eager to try ur firmware
does it already has installed qos?
or do i need to install it myself?
going to pair it with my ZTE MF680

EDIT
my MF680 and Huawei E353 can be use straight and browse the internet
Before this i use AA rc1, then straight upgrade to ur openwrt firmware and the ModemGUI, only detect ZTE MF680, not Huawei E353, well not bad as i rarely use E353, consider good already MF680 can see signal
The prob now, i cant seem to install "luci-app-qos"
Pls help, i really need qos, cant you guys include the qos in the image?
It shows


This post has been edited by azim61: Feb 9 2013, 11:40 PM

my MR3420 V2 frequently DC..already upgrade to latest firmware..is it my E367 problem? try to flash to openwrt and sucssesful..but have no idea how to connect to 3G.. does it auto connect or we need to manually setting the openwrt?

on your V2 original TPLINK stock firmware,

under the 3G/4G in network setting, IDLE timeout: 0 <-- need to set zero

so it wont DC

if u did V2 openwrt : just follow below to setup

- login 192.168.1.1 ( you will see LuCI Gui interface )
- click login
- go to System
- go to Administration
- key in your new password ( For web Gui )
- re key in your same password again
- click save and apply
- go to Network
- click Edit on Wan ( 3G wan )
- select UMTS/GPRS/ED-VO protocol
- click switch protocol
- Modem device ( ZTE modem = /dev/ttyUSB1 , Huawei modem = /dev/ttyUSB0 <- last is zero )
- service type : select UMTS only or UMTS/GPRS
- Key in your ISP APN , ( Unet, Maxisbb, bbnet, celcom3g, u3g, my3g and so on )
- Go to ADvance setting
- Modem init time out: 5 ( key in )
- Use gateway Metric : 0
- Tick the box of : if uncheck, No default route is configure
- Use custom DNS server : 8.8.8.8 click the icon at the end
- second roll: 8.8.4.4
- LCP echo failed Threshold : 0
- LCP echo interval : 5
- Inactivity timeout: 0
- select Wifi
- click Edit
- select your wifi prefer channel 1~11
- enter your wifi name in ESSID
- go to Wireless security
- encryption : WPA2-PSK
- key : wifi password
- click save and apply
- then click enable to on your wifi ( if u need it )
- now go to System
- Reboot
- click Performs reboot
- plug in your Usb modem after
- wait for reboot finish and enjoy

thanks mr. chuah for the reply..
on my V2, i need to select "connect manually" or "connect on demand" in order to be able to set the idle timeout..if i select connect automatically, this idle timeout function cannot be key in..

and my MR3420 seem difficult to identify my E367..sometimes it identify successfully, sometimes it will keep to identifying... and sometimes it show "unknown modem model..."

set to connect manually first -> then set IDLE timeout = zero /0 -> then set back to connect automatically

Guys, why when i try to click "save and apply" in openwrt, my router keep disconnecting and the webui does not responding. I also tried to restore to factory default and rebooting multiple times, but the same problem still occurs. Even when i restore to original stock firmware and flashing back to openwrt, my router keep disconnecting when i clicked "save and apply". Please help me.

lan or wlan connection? if ur editing ur wireless setting.. of course it will dc if ur using wlan..

Im connecting my pc to mr3420 v2 using lan cable, but other devices in my house just use wifi to connect to the internet. I look at the guide chuahcs posted, but it says i need to configure the 3g wan. But when i look at the openwrt network interface, only LAN section is available, WAN and 3g are not. So i edited the LAN section (i tried to edit in the WAN section, but it wont connect to the internet)

i also have plugged in the lan cable into WAN slot on my router, but i cant open the openwrt WebUI after that.

can u do a reset?
then edit only the wan section.. ur lan cable must be plugged into the lan port.. not wan port..

finally can..need to wait awhile for the uptime to be shown..its a bit faster than stock firmware..thanks!

if u put 5 second in setting, then dialing will be done in 5 second ,..

is it modem init timeout? yeah i did put 5 in there...dunno whats the problem that make it slow to connect to internet.

Thanks mr. Chuah, i flashed to openwrt and now my modem uptime is10hours ++..and my connection also stable until now..very nice..i ama happy with my both modem..what if i change to e398? Any improvement?

And guys, how to set dns in openwrt? First i key in 8.8.8.8, then i click the small icon with the plus sign..nothing happen..just the green plus sign become red cross sign..

dont forget to save and apply.. then reboot ur router, relaunch ur browser...

thank you bro..it won't work in IE..i manage to set the DNS in firefox..