Edited.

This post has been edited by sHawTY: Oct 20 2013, 02:34 AM

Edited.

This post has been edited by sHawTY: Oct 20 2013, 02:34 AM

my TPLink WDR4300 running fine without restarting average uptime is 40 days.

Anyone know how to boost the wireless signal, it terrible wireless signal on this router. I just get 2/3 bar or 1/3 bar of the signal and the router just beside my room only.

Edited.

This post has been edited by sHawTY: Oct 20 2013, 02:34 AM

ya compare with using the original router from unifi is better than wdr4300.

Anyone?

try 3.13.21 Build 121226 Rel.39036n .its pretty stable.

Edited.

This post has been edited by sHawTY: Oct 20 2013, 02:35 AM

cannot use tp-link tether...when they going to update the firmware for malaysia user?

Edited.

This post has been edited by sHawTY: Oct 20 2013, 02:35 AM

anyone upgraded stock antenna to 8dbi antenna?

So the solution is to download the firmware? I bought the TL-WDR4300 as well because the promoter said it supports Unifi (even had the 'Supports Unifi' sticker on the box), but when I finished setting up the router, the wireless network can be detected and connected to, but there is no internet connection.

I spent hours trying to do just anything but then I gave up and switched back to the old router and now I am here, finding solutions.

Is this router can support IPTV?

Yes.

I bought this router and use for 7 days. It was fine all 7 days, suddenly there is no Internet connection this morning. I check, reset the router, redo the quick startup. The wan indicated it was connected, when i try to ping google.com it took forever. I tried to redo quick setup again, it failed 2nd time to connect to internet. Then, i brought up my old tm given router dir-615, plug in, and it works perfectly.

Guess i got a lemon unit and need a replacement. Anyone facing this problem?

Hi guys. I'm no networking expert but I would like to share my experience using this router on UniFi. I bought myself a TP-Link TL-WDR4300 just yesterday due to the unavailability of Asus N16. The 1st thing I did upon unpacking was to check out it's menu and all then proceeded to upgrade it's firmware.

This is where I did a mistake as the international firmware is not the same as the local "UniFi supported" version. Upon installing, I lost the option to set the router to "UniFi mode" and also lost the "VLAN ID" assignment option. Noticing this, I re-installed the firmware "TL-WDR4300_V1_130612(VLAN)_My" from HERE.

2nd mistake was during the firmware upgrade, the progress bar was meant to run twice but for some reason, it hung on my Chrome. Then I restarted my PC and the router together. After that, I keep seeing Time out due to PADO error in the router log. I almost assume this as a lemon unit until I did a hard reset (via the button) then restore factory default via browser and then re-install the same firmware stated above all over again. This time, the progress bar ran twice (1 for installing the firmware and another 1 for restarting the router). Upon completion, I ran the quick setup and key in all the necessary details and voila.

I got this instead of the PADO error:

Hello guys, i just bought WDR4300 , have done all the setup n its working but my PING for BF4 jumping from 10ms (with TM router) to 110ms (with WDR4300) . Anyone face the same problem? Any solutions?

Anyone manage to upgrade to WDR4300 (v1.7) on 3.13.32 Build 130612 Rel.83937n to run OpenWRT? I tried to upgrade the firmware but the page doesn't seem to be responding. What am I doing wrong? i followed the steps in http://klseet.com/index.php/tl-wdr4300-v13

Please help

anyone could connect to the internet for UNIFI using this TL-WDR4300 router?