Bro your gflops is low. Already on service pack 1? 4.4 should get 120+ gflops.

Stressing my ram @ 2400mhz 11-13-12-35 2T, i already loosen up the ram timing. So far 50min stable prime95 90%>ram. Should i stick @ 2200mhz 10-11-10-28 1T?

I set it @ 1.65v. Here's 2400Mhz 10-12-12 2T, 1 hour stable. Will stress test longer tonight.



This post has been edited by ketapang: Nov 6 2012, 08:23 PM

Going strong for 5 hours but ended up 1 error, 3 cores still going. Need to loose the timing again.

How about max fft? I use 8k min & 1792k max. Usually I will get error around 10min if not stable. I read somewhere 1792k & 1344k is good for checking instability.

This post has been edited by ketapang: Nov 7 2012, 01:16 PM

So far 3 hours stable with a bit loose timing, using your recommended setting. Will try for long run tonight.

Successfully delid my 3570k.
http://valid.canardpc.com/show_oc.php?id=2574826

Okay, here's the result after delid :
8 hours prime95, 90% ram, 4.5Ghz @ 1.3v.



Before this, my temperature will hit 104-105c @ 4.5Ghz. So delid improve my temperature by 9-10c. Not to mention, im only using cheap TIM here, deepcool thermal compound . I bet i will get 12-15c improvement if i use liquid ultra . Now im perfectly stable with this speed . Btw, it took me around 10min only to delid, seriously im really glad i do it right.

---

Added on November 9, 2012, 9:37 amUpdate:
It seems 4.5Ghz is the max oc i can get with my cooler. 4.6Ghz already hitting 104c (after 20min) & I need at least 1.4v to be stable without any WHEA error. I really have a bad chip here. So 4.5 it is.

This post has been edited by ketapang: Nov 9 2012, 09:37 AM

Thx bro. Idk what happen to me yesterday. I was finding stability for my ram and when i saw the temp, i was like "ok delid time" . 100Mhz might not be big improvement but it really worth it. Seriously why Intel use those really2 cheap TIM. When i touch those stock tim, its already hardened and there's only little contact between the IHS and the die. No wonder the temp is really high .

I think you can hit 4.7-4.8 with delid + liquid ultra. Even wit cheap tim i manage to decrease the temp by 9c.

Not exactly but for ihs to die tim, yes its the best out there because its almost identical to fluxless solder. Metal>TIM in heat transfer.

---

Added on November 9, 2012, 7:49 pmNot to mention hard to remove. Anyway bro you already order liquid pro? how many months it takes to ship to malaysia? any local dealer you know selling liquid pro?

This post has been edited by ketapang: Nov 9 2012, 07:49 PM

How about the price & payment method? Might interested in getting one.

Looking forward for that liquid pro bro.

This post has been edited by ketapang: Nov 10 2012, 06:49 PM

Guys what do you think the right price for delidded processor?

3770k too pricey for me bro. Not really satisfied with my current proc, 1.4v for 4.6ghz. Might go for another one later.

Need to see 1st if my budget allows.

Finally found the lowest voltage for 4.6Ghz, stable for 10 hours.

Thx bro. Liquid pro still not tested yet? looking 4ward for it.

Up to you bro.
Btw this is still using cheap deepcool tim, wait until i replace it with liquid pro. possible 10c lower than this one.
With this voltage i should be getting around 4.8-4.9 but my proc is so......

Proc ak ni manja sgt, nk "susu" lebih. Klu xnak delid, go hunt that golden chip!

---

Added on November 13, 2012, 7:59 pmMine 2200 @ CL11 1.5v, lazy to tweak . I could run 10-11-10-28 with 1.575v.

This post has been edited by ketapang: Nov 13 2012, 07:59 PM

The tightest timing i could get is 10-10-10-25 2200Mhz with 1.65v. I could boot 2400 CL11 but really hard to make it stable, even after loose some timing only stable around 1 hour then crash. So i ended up @ 2200Mhz, so far no problem at all.

This post has been edited by ketapang: Nov 13 2012, 08:29 PM