around 1hour waiting , check for my carb and the tak tak tak sound..

@alexei - o0o0.. thats mean just effect on plug only?
no other engine parts?

---

Added on November 3, 2011, 11:37 pm@shyan - last time i got see one swing arm.. ppl said lighter than ori.. forgot what brand.. for rear disk brake.. better u go buy 125z punya.. much better.. ori

This post has been edited by budakmentah: Nov 3 2011, 11:38 PM

Carb how?? Ok is it? Raiderz got set his carb????

@Mental i just need to change my arm because i need to masuk disc brake so really not mkn brake pad...I felt that all aftermarket parts will makan brake1...My next target~ BREMBO masterpump!!! I found 1 in US and he's sell 90USD...Still consider buy or not...But still thiking sin la..

weyh.. gila la u.. no need brembo la.. later u bike become hot. itu rempit2 tengok sure they target ur bike.. just use nissin 125z ori.. dont buy local..

Hrmm...So i thinking la..Cause ori nissin also cost me RM200 new 1...Rm300 new 1 Brembo...

i suggesting u just using nissin. make sure the real ori one.. dont buy clone..
and use good brake pad.. dont cap ayam..

carb set back coz fc high , everything ok..rider dint set coz he dont wan pay rm30

Rm30 per set..>,< little bit pricey... Lol..Then tomorrow what time yumcha??

@Mental...I ask sentul is RM200 for 125z ori nissin...From yamaha 1...Just brake pump..

tomorrow evening ok?

Ok~

if true ori.. grab it.. dont waste on brembo.. but to install on lc.. need some modification.

I know 57mm what to do and try d....

62mm i got the idea, planing stage....need wait until 57mm die 1st....

U mean parts to use and change right? Like formula?

As for 58mm, 60mm and 61mm, phase out liao...unless got ppl try then can share experience la....

The practical 1 would be 54mm, 57mm and 62mm and 63.5mm

54mm, I hav recommendation....

I think shyan set up for 54mm is quite good....

---

Added on November 4, 2011, 2:27 am@thianz,

Finally found the balancer shaft for LC at Klang area...., after asking more than 10 shops then only know selling at Klang....WT....

Less than RM 30 without the balancer just the shaft....and no need hammer in just plug in and it lock the handle hole properly....

Anyone need PM me....

Now feel better comfort......

Now considering whether to put back the the ori balancer or......

This post has been edited by NewGUY: Nov 4 2011, 02:27 AM

--

This post has been edited by alexei: Nov 4 2011, 11:15 PM

@Bro eric~ THks...But need to change the MJ first la...actually now my spec is still not enough fuel at least i found 107.5..The balancer handle can't DIY install??? I think u can sacrifice the old handle to install a new 1...><

---

Added on November 4, 2011, 11:25 amBut i got a friend who install Fz cam + Fz block + nobi...And reset carb change MJ...So far he said power not too strong and got power...Neh~ Bro eric and b.mental ah...The guy who follow us last time to TT 1 ah...3 spoke racing boy sport rim ah...and last follow us till klang that guy ah...

This post has been edited by 163119779: Nov 4 2011, 11:25 AM

@alexei - so just need to pull choke when wanna start engine.. after that pull back to close. ok2.. thx for info..

@shyan - o0o.. he using fz cam + fz block?

--

This post has been edited by alexei: Nov 4 2011, 11:16 PM

Balancer need install correctly....

Just put in the balancer, new handle no balancer also la....

Of course, not so strong for FZ block bcos compression 10.4 less than ori block which is 10.9.....

@Mental Ya...that guy ah...Live in banting 1...><
@Alexei... Sry..>< Menas i not reach the limit of my block which i think can twice some more juice..><
@Bro eric...Erm...Heard that adding gasket can increase the compression of the block is it?

Haha..just log in to this new thread..abit late

i just wan to put in 1st page. in case ppl come in and ask for engine modification.. then can straight refer to 1st page..

since the 1st page for 'major mods' section is empty since V1 until now.. and no1 update it..

i decided to update it. bagi semua formulae.. write nice2..

example like what mods need to pair with what type of parts and stuff..

altho need a bit of ur time to write it.. but its worth it wan.. mayb in future i wan to mod... i can straight refer 1st page.. then ppl wan to mod.. wont scared they got cheated or something like that..