I see you still remember me telling you what i said . Good job.

Guan from EA selling slotted rotors plus installation for 380/pair. pads i dono

---

Added on December 20, 2011, 12:20 amthe mazda6 did RM53 171km ron97

if ron95 its RM36 for 171km

RM36 - 18.9 litres for 171km

9km/l for a 300whp car not bad .



This post has been edited by ThunderGod_Cid: Dec 20 2011, 12:20 AM

No beast lah

Your Mazda is sitting with the same league as rx8 or even faster. Almost same as rx7

This post has been edited by Vervain: Dec 20 2011, 12:24 AM

faster, definitely

Never sit on it. When are you going to fetch me?

one day . One fine day

guys, when i making slow braking.. there is this occasionally "wweee" sound from the brakes.. Brake pads less than 6 months old.

Is it the installation not so good?>

Should be Brake not evenly contact. or your existing disk already warped.

Vervain ride being pimped and pumped lols



This post has been edited by mxsteven: Dec 20 2011, 10:33 AM

What does this mean?

bengkok lo... need to find mechanic to check it ^^

---

Added on December 20, 2011, 11:38 am^^ slurrrpp


This post has been edited by eriyque: Dec 20 2011, 11:38 AM

the BOT kits for Campro.... ‎5.5k full kits + installation + dynotest ...Management will be using SMT8 + boost management with sub injector. Credit card accepted and for Maybank card there is flexi 12 month payment.

Poisonous stuffs... haha

boosting how many bar??
mine one boost 0.5 due no install 3 bar map sensor... but mine ecu still manage to read it until 0.5
i think its ok for temporary cus i havent upgrade my internal part...
after upgrade only add the sensor ^^

Dyno'd?

You punya mitsu TOB bila nak on?

---

Added on December 20, 2011, 6:58 pmHow much u've spend? And how much more to complete?

This post has been edited by coinstar: Dec 20 2011, 06:58 PM

around 8-9 k...
thing that i have install
Td05 with custom manifold
Td05 aftermarket downpipe
Sard fuel regulator
Walbro fuel pump
275cc injector
Vr4 intercooler with custom piping
Elbow bending s.steel exhaust piping 2.5" , muffler inlet 2.5" outlet 3"
Emanage ultimate
Apexi el boost meter

i think this is normal for stage 1 setup....
next month will change my current clutch to trinity racing clutch and two port brake

for internal engine part , not to soon ;p
maybe for low boost purpose only

trust me... management is very important.... if u dun have a proper ones it will damage ur engine n u spend more later...

---

Added on December 20, 2011, 9:44 pmtomorrow will dyno...

---

Added on December 20, 2011, 9:45 pmMitsu TOB anytime.... if u wan then just send ur car

This post has been edited by mxsteven: Dec 20 2011, 09:45 PM

[quote=mxsteven,Dec 20 2011, 09:42 PM]
trust me... management is very important.... if u dun have a proper ones it will damage ur engine n u spend more later...


My mech adv me say with e.utimate without 3 bar map sensor,it can read til 0.5 bar .. and also can maintain low boost

But if i add in the 3 bar map sensor ... i might getting higher boost;
so i think only after i upgraded my engine internal part.. then only add the sensor to read higher boost .

This post has been edited by eriyque: Dec 21 2011, 02:35 AM

alot of high end goods.