u can change the barb size, but its kinda rare, i only have seen 1 shop selling it,

for performace, maybe there i a bit of restriction at the radiator...

from 1/2 inch to 1/4 inch and back to 1/2....

erm....

WOhoo...

COOL.....

Might think of doing that mod soon...

Anyways....

COuld this fan be connected to the molex that comes with ur relay pump ?

maybe u can make an extra connector for this fan

U could try and PM Metalzone,

maybe he can customize u a NIrox P2800 with a 1/4 fittings....

Here is my New Watercooling kit.



Here is an extra heatercore taken from Charade Detomaso.



Maybe i shud use 2 radiators

hehee....

erm cracks...

i tested the reservoir already....

No Cracks.... maybe the rupa only... hehehe.....

actually there is one crack, a small one, i managed to patch it with ePoXY . it cracked a bit, while screwing the barb onto the reservoir, CUAI !!

heehe....

Yeah.... waiting for the relay box to arrive and maybe modding my P2800 this weekend add some fan, like u did SHAH

ehehehe....

I know that Nirox is not suitable for the dual rad, and summore i dunt think its suitable for the DD TDX ..

anyways.. just tryinh it out first... maybe get the Aqua king Soon.


@shah,

MOd jgn tak mod..... Beli jer Glade tu kat Giant... Sambil sambil MOD- Kerete bau wangi skit hahaha.........

erm....

Leak ehh...

Luckily Bro Amok told me earlier that i had to seal the impeller cover with epoxy..

That was the first thing i did...

anyways.... U shud try it....

Mine did not leak

GOOD LUCK

@boboy,

Wahh..... Bocor ...... anything in ur CPU fried ??

@ikan_semilang,

Looks like the kit uses a 1/4 fittings and tube .. or is it 3/8 ?

Wait it uses 10/8mm tubing size.. erm...

hehe...

GOOD LUCK BRO, I PUT EXTRA EPOXY, to make sure it doesnt leak... hehehe.......


Delrin comes in liquid form or in pieces like acrylic ??

erm....

how much does the valvoline coolant will cost ?

erm...

hehe...

i tried my WC KIT yesterday for a first tim run...

My Reservoir got some leakeage at the bottom and my pump lekas at the barb...

so i resealed the barb with silicone and resilicone and epoxy the reservoir

doing another test tonite, maybe after dinner

u mean to add in another pump and radiator ?

so its.

RESERVOIR --> PUMP ----> RADIATOR ----> PUMP --> WATERBLOCK ---> RADIATOR ?

I think it shud be like....

1st RESERVOIR --> PUMP ---> RADIATOR ---> WATERBLOCK ---> 2nd RESERVOIR ---> PUMP ----> RADIATOR ----- > 1st RESERVOIR.

Darn....

I'm blurred already, it looks almost the same as the setup u have suggested


anyways,

if u have a powerful enough pump,

u can just add in another radiator without adding in another pump.

Well I am not an expert in this, but i am sure that u need a powerfull pump to drive 2 Radiator

peace

Rite now, i am Dry Testing my New Wc kit, it seems there is no leak...

but , there are a few drops of water coming thru the Nirox Pump..

is that normal for first few starts ?? But later after running for a while, it stops dripping.


i am trying to leave it to run for another day or two, see how it goes


Thanks

the propeller base doesnt have any problem.... sealed that one again... hehe...

another round, just to make sure it will not leak in the future....

i found out the leak was from the propeller shaft, on the top of the pump.

i took out the top cover to install a fan , just like Shah Did....

so i sealed the hole there and now no more problem.....

dry testing now, will get back to it, this evening....

U can Change ur Pump Fittings from 1/4 to 3/8 ,

but for ur Waterblock, i am not sure, the size is fixed at 1/4.

i think ur radiator fittings are fixed at 1/4 too...

so the only thing that cud be upgraded wud be ur pump.

currently the pump is still on test....

hehe....

the fan blom test lagi....

i think it sure helps.... coz the pump itself is hot...

erm.... Mine leak too... i used PTFE that time, then i reopen te fittings then i resealed the screw side with silicone at the pump and fittings...

reinsert the pump and let it dry for one day...

then retest, no leak

before this, i use to put my pump inside the casing, but the pump is submerged in a reservoir, so far no problem.....

i dunt think there will be problems...

if u go to the watercooling club thread, u will see a lot of people put their pump inside their casing

i dunt see this nirox pump of mine goncang that bad, i am still using the black suction cups that came with the pump... but its not in the casing yet, still outside of the case.

Battery Water contains Manganese, usually around 0.003ml i think...

does this manganese affect (corrode) the components such as pump, radiator, waterblock ( metal parts ) ?

Anyone knows ?

i am just curious coz i have seen a few battery water not containing Manganese, so wud it be better if i use the one with or without mangan....

Kinda hard to find Air Suling.... unless u work in a lab