y is it the manufacturer still make x58 platform ?
aren't it phasing out anytime soon ?

any news on official release and spec of lga2011 platform ?

eh, does the new linpack used for SB stressing gives any difference on this x58 platform ?
maybe more gFlops or something .
might as well do a bit of comparison

memory to OS = 0MB .
priorty = above normal

run in diag mode .

should be all core running 100% during linX .
can try check affinity status in task manager as well .

what ram r u using man ?
and iinm scale of 4.4ghz with 2k+ ram should be around 67gFlops .
not really sure .

oh sorry i didnt scroll further .
anyawy, thx 4 d info owikh .
cause wanna try for 4.4ghz .
finally boot up my system .
sadly no internet, cable not long enough to route to my PC .
will post pictures n stuffs on WC .
maybe by next week since i'll be busy tomorrow >.<"
and going back to kajang

could try first .
vCore vary depends on chip bro .
yeap even i use 930 oso i use 21x instead of 22 on turbo mode .

---

Added on February 28, 2011, 10:57 pmwhat does prime really push and what does linX really push actually ?
i've forgotten .
seems like sometimes could get solid 12 hours on prime and fail linx instantly or vice versa >.<"

This post has been edited by monsh: Feb 28 2011, 10:57 PM

try 1600 7-8-7-21/24
tfaw 30
trfc raise a bit
must work around it
not really good at ram timing
try ask owikh .
he's ram lover
try raise voltage as well .
should be able to do 1600 cl7 at 1.61v something like that .
2000 is possible .
try cl9 1st .

yea try 88 and play around with the RTL .
2k cl9 not sure .
try 61-63-65 .
ergh left the clocking on this board for so long .
forgot already the scaling .

---

Added on February 28, 2011, 11:37 pm1600 cl7 should have similar result to 2k cl9 iinm .
yea well imma go back to home this weekend and clock my PC ^^,
1600 cl7 is possible .
i used team elite and tried around 1200 cl6 is bootable and stable ^^,
what chipset not sure .
simply try and successful.
team elite ram used on my AMD rig .

This post has been edited by monsh: Feb 28 2011, 11:37 PM

if ur willing to try 1.7v go ahead ^^,
what's d vtt u running for 2k ram ?
and try push a bit on the vCore .
maybe low on vCore .

there was discussion bout this b4 .
but i think its due to overtighten proc or something .
try ask owikh .
he explained this situation b4 .
forgot edi .

0095 is older thatn 1005 ?
what's d best bios for now ?
i want to flash my r3e this weekend .
and start clocking again if i have the time ^^,

owikh killed his r3e bcos of 1.6v vtt last time .
u only need around 1.4v vtt for 2000 ram .
ioh n ich dont have to touch .
if play above 210bclk then only play with ioh iinm .

nvr had experience with the r2e .
vtt 1.6v is very high man .

yea man .
even 1.4v is very hot already without WC .
dat's 1 of the reason y i stop clocking and proceed with my project .
finally grab the bits waterblock to counter this problem .
no thermal sensor, and its already hot like crap !

couldn't imagine running at 1.6v vtt .
i tried 1.5v and i couldnt hold my finger for 3 secs on the mosfet .
must have reached somewhere around 100C already .

gila babi rich guy !
this one kaw2 cun wan !

what rad ur using ?

yeap the scale would be different since one runs on triple channel another one runs on dual channel .
but if both runs on dual channel im not sure its the same or not .
ask the sifu