i used the TCP and UDP HMMaster suggested.......but still cannot start.......
i tried to connect to the Razorback2 server, but it said something like the server seems to be full...
then in My Info, i'm connected to a Low ID
then i dun understand the rest of your question....
what should i do now?

I changed to 1235 and 1236.
Anything is better than 4662 and 4672.

aiyume
have u configure ur router ?
done the port forwarding ?

tcp port have to charge ...
udp port can remain default ...
i have try this and the speed go up to 40KBps....
tcp port 4242 is fast

err......how? i'm noob in router and port

then in My Info, i'm connected to a Low ID <===

If you are getting a LowID, there are normally 3 things that can cause that.

#1 - the inbuilt windows xp firewall (you should turn this off.)
#2 - a firewall (you should allow/open the emule ports in the firewall)
#3 - a router (you should forward the emule ports in your router). It is also recommended that you change the default ports (TCP4662 & UDP4672) in emule because our ISP blocks them ..

identify your modem here & do port forwarding on it.The ports can be any value between 1024 and 65535 But you must remember to alter the config of your firewall/router and restart emule (never use port 5000)

This post has been edited by fendii: Apr 7 2005, 04:26 AM

guys, i hv set the port which u suggest in this thread but it still not works with my emule. it can achieve the maximum dl / ul speed in few minutes, after that, dl / ul speed remains zero.

Is there anything i hv done wrong?

- High ID (OK)
- Low ID (Behind router/firewall) Go to Network Broadband forums to port forward your router and firewall setup. Pls don't use the default 4662 port TCP. Streamyx blocked this port. Use 4242 or other port anything than the default port.

dun think streamyx will block any ports ler.. im getting speed up to 40k's with this port.

i did what u all suggested in this thread and yes, my emule is in High-ID status but the dl/ul speed remains zero.

Actually it works until this morning. Dunno wat's happened with my emule....

have you tried downloading a high-sourced file off eMule?

oh yes, check here too..

This post has been edited by fendii: Apr 7 2005, 01:17 PM

yup, i'm downloading the high-sourced file....btw, it works again...now the dl rate is 30++KB. i found out that it works when i disconnect the KAD and connect to server only.
if connect to both, the dl/ul will remain zero.

erm.. i think today there is a problem with the internet in malaysia...

KAD should get you better speeds

have you tried checking your eMule settings ?

http://forum.lowyat.net/index.php?showtopic=143943

guys...
I've foward my port range from 0 to 65000.
basically my bit torrent can run fine, tested using BT client azureus, any port in this range including 4661 is reported to be OK.

But with OneMX (eDonkey client), I'm still getting the lowID message. Anyone knows where's the problem? The port forwarding part should be fine right?

BTW, none of my dl can start after hours of waiting

Pls help, thx.

This post has been edited by Hornet: Apr 7 2005, 10:13 PM

oh hi hornet, if youre one of malaysias streamyx suscribers, perhaps you should give emule a rest for a day or two since there has been some connection problems going on lately..

aiyo i have no idea to port forward my Aztech DSL305EU modem router. Wat to put into the IP address column??? and i got this private ports and public ports HELP help

IP Address as in your local IP
go to command prompt and use "ipconfig" to check

Private port and public port just put the same

yes yes i sucessful set up my port forward setting already so complicated aettings man..........now i'm FLYING with emule

which server you guys dl from?

most of the time i connected with Razorback2.