wow that means i also got 4.3ns ram!

ei pc depot sell u the rams got discount or not? i heard that some ppl will keep asking them to gif discount and they will gif like 10-20 ringgit

I push my BT-D43 (512X2) to 230FSB at 2.5-3-3-8 today on 3.2V , it's running rock stable pass memtest , now oledi running 4 hour prime 95 without any error.
Will OC futher tomorrow..

ur bt d43 likes vdimm? what mobo u use by the way?

wow ! now that's cool!

btw: when did you buy your ram? date?

normally DT43 can run 250mhz at least. Try straight go to 250mhz with loose timing first, then slowly try to tighten it.

Hi,

I tested mine 2x512mb, dt-d43. When running 1 stick alone can do 225mhz@ 3338 with 2.8vdimm, it could pass memtest 3 passes at least. But when running on dual it shows errors even in the 1st pass. I read someway ealier it 'cause the double sided thingand not happy with nf7s ??? I am now using them at 200mhz with 2.8 vdimm.

I think ddr ram is going up and read that in China web sites yesterday.

i guess it like high vdimm coz when i change the vdimm to 3.0V it's not working , i using ASUS P4P800SE .

i buy it half year ago.

i'll try it 2molo .Thanks for the info

hmm .. feeding 3.2vdimm ar ..

you using that for daily usage ? you got any fan blowing on the rams ?

won;t the ram get brun due to high temp ?

Yup, i on it all the time.Download movie ma.The ram not hot as we thought lah, it's still ok . I'll take the actual temp. 2molo went i get back and post it here.

This post has been edited by CwL: Apr 7 2005, 02:25 AM

hi guys, may i know wat is 1T, 2T ?? wat is the difference? how to set in the bios?

For Hynix coding, D43 means DDR400 with 3-3-3 timing. D4 means DDR400 with 3-4-4 timing. While D5 (donno about D50) is DDR500 with 3-4-4 timing.

You may get the ram part file here : http://www.hynix.com/eng/02_products/01_dram/down/DDR.pdf

I just got a BT-D43 512 X 2 today.

Hrmm.. but I'll try strain it today

But my board limits my FSB, so I'll have to adjust from the FSB/MEM multiplier

UPDATES:
=======

Failed Prime 95 after 1 minute at these settings. Weird

FSB = 333, Divider 3/4, RAM = 442 @ 9-3-3-3 @ 2.9V

Anything wrong with the figures?

Now trying with 3.0V.

This post has been edited by KeNNy: Apr 7 2005, 06:57 PM

bt-d43 doesn''t work well on tight timing. try loosen up the timiing abit. bt-d43 work best on 2.5-4-4-10 or 3-4-4-8. vdimm from 2.7-3.1 depending on the chip.

jz my 0.88 cent opinion

Could it be my board?

But anyway what timings are you running personally?

I tried the same thing 445Mhz @ 9-3-3-3 @ 3.0V. FAiled

Will put looser timings later and see

tried set looser timing...
then u prime95 again...
set volt at 2.9, if fail up a lil bit

well i do some reading bout D43...
D43 can't seem to push eventhough raising the Vdimm...

persoanlly i'm running 250 *2 = 500 Mhz @ 2.5-4-4-10 on daily usage at 2.6V

was able to benchmark and memtest stable at 285 * 2 = 570Mhz @ 2.5-4-4-10 at 3.0V

i'm using dfi ut 250GB mobo on amd64 socket 754

This post has been edited by shadow_dweller: Apr 7 2005, 09:07 PM

from my exp, d43 does not really need a high vdimm.. mine can run 260mhz in dual channel mode @ 2.5-4-4-8 1T @ 2.85vdimm

erm .. i think bout the vdimm thing it depend on the chip. mine kinda need higher vdimm for stability if i oc the ram to higher frequency.

coz when i ran 280Mhz on 2.9V vdimm it wasn;t stabel but when i up it to 3.0V it was able to run memtest for half an hour without error.



This post has been edited by shadow_dweller: Apr 7 2005, 09:44 PM

From my guess, it's most probably my board that's limiting it. Perhaps the Memory Bus speed cannot sustain anything about 400Mhz properly

From an engineer's point of view