Wahhh! Orang Kaya!

wuu! later can lend me your 4850GS to do cfx with mine GS!

How much you bought the WD Black bro otromen?

4ghz is still in process, 3.8ghz cannot achieve with stock 1.4v, have to pump a bit to 1.425v maybe bcoz of vdroop or something..
Tested with prime95 just now but my rig hang suddenly with 5 minutes left to the end of the 1 hour test..

---

Added on January 4, 2010, 11:17 pmCan no prob but when u return to me have to replace with HD5850

Bought the WD Black for RM315 from Cycom

This post has been edited by cloudwan: Jan 4 2010, 11:17 PM

no need to stress the ram first.. loose them.. quad not the same.. hard to drive.. go²..

Ya ka? I did blend test when it hang just now , so it's advisable to do only small FFT or large FFT test meh?
Ok i'll do the retest bro.. Let u know in an hour..

P.S> My streamyx is acting up again, kept dropping line.. Demmm

or maybe set 1066 ke.. depends on mobo mul though..

Hmmmm passed 3.8ghz, going for 4.0ghz next, hopefully can pass on current cpuvolt



BTW the prob earlier could be bcoz of the ram ah, now trying with the ram volt bump up a bit to 1.64v

we expect moar brader cloud..kekekek

sure whole night cant sleep right? kekeke

Awesome bro otromen! will wait for more result from you!

BTW..HEPI BESDAY KUNTAU..huhu

Ya, cannot sleep, keep restarting pc then try, then hang then try again
BTW tried 4.0ghz but it was a no go.. Only tried with the vcore up to 1.45v only tho, then i got sleepy
Will try again today when i get back from work..

BTW kunta, HEPI BESDAY!!!

HAPPY BIRTHDAY KUNTA~

to celebrate it, OC ur proc with 2.0V Vcore~

ni x buleh jadi ni, c2 x2 550BE abg -pWs- pong buleh run 3.8GHz w/ 1.424v mah...

joke aside, what's ya tmpin2 bro? sensor problem or real? it's rather high imo.

also, do try to put ganged mode (some performance hit but gud for stability iirc) to ya ram & bump ya vdimm a 'lil. 1.7~1.75v won't hurt.

HEPI BESDAY too kunta, u have d same birthday as my bro...

This post has been edited by ah_khoo: Jan 5 2010, 09:46 AM

maybe becoz that tmpin2? aiyo 80c..

Slow slow la bro, it's hard to oc when haf of ur brain want to sleep
Ok i'll try those setting when i get back bro.. hope that the C3 i got isn't a dud..
BTW cpu temp max around 62c is still ok ka? When i change the cpu i didn't reapply the thermal paste just put a little bit at the center with the old paste

I donno bout that crazy tmpin, since purchase this mobo i been trying to find out which sensor is that but to no avail..
At 1st i thought it was the NB, but even after putting on the NBcooler ah_khoo gave it remain the same..
Even the pwm i already put the alu sinks but still the same also.. aiyooo
Do u think i need to put the sinks on my mobo ferrite chokes also??

This post has been edited by cloudwan: Jan 5 2010, 09:56 AM

tmpin0 = cpu
tmpin1 = sb
tmpin2 = nb

so must search nb cooler kaw²
put old fridge.. muahaha

lol... was just pullin ya leg bro... it will take you sometimes to figure out how to tame d chip even u're familiar with d board, diff chip diff "pattern"... i'm quite sure u'll give us d result we want in a week or few...

load temp @ 62'c is kinda high to me, reapply d thermalpaste lah... dun be so stingy mah...

as for tmpin2, does it remain d same even b4 d stressin start or it increases gradually until reach 80'c?

i dun think u need to put pwm heatsink on those chokes...

This post has been edited by ah_khoo: Jan 5 2010, 10:40 AM

hahaha i think tmpin2 just static -+2c..
sensor prob?
i reading somewhere.. gigabyte said 80c is normal.. lol

Not stingy bro, just laziness on my part
My tuniq-tx2 already finish so have to make do with my Xigmatek Thermal paste, donno good or not
Haihhh really can't wait to get off from work to try again..

Yup that tmpin2 is static, start my pc already that temp, if stressing pun only -/+2c

aaaa....
temp kt hw yang mane ptut refer?
yang temp core or just temp?
yasterdy continue ma homework reached 3.8 stable with prime for 2hour, max core temp is 57c, max temp is 92c, ok ka?
and try to reached 3.9Ghz, 10min after prime without error sign, my rig were restart,any guide sfu2?

try to lower down your NB and HT speed to 1800Mhz! and slowly increase it up!

Not to forget the voltage as well! Aiiyaarkkk!

315 nyum nyum!


This post has been edited by verdict: Jan 5 2010, 12:28 PM