Top RM130pfr & Bottom Rm110pfr is for melamine board or 3G Glass?

Yaay! UD called me and said that my "Garlic" solid top will be installed tmrw!! can't wait! Crossing fingers and toes that it will go smoothly

kitchen in Mieco (congo wenge) + black galaxy granite top~





Wardrobe

---

Added on March 15, 2011, 1:12 pmWe concern on better design + quality~

Let's see our new wardrobe, hope you'll like it~













This post has been edited by Erny_Looi: Mar 15 2011, 01:12 PM

Got a question.
I'm planning to seal one of the entrance so that I can install a kitchen cabinet. Just wondering if there is any particular materials that I shouldn't use?

Ie. can plywood or chipboard wall support the weight of a upper cabin? or should I use a brick wall?

Nice! Thanks for sharing~

Super nice. Who is the vendor and how much if you don't mind to share? Thks

---

Added on March 15, 2011, 7:11 pmHi u have contact no for UD?

---

Added on March 15, 2011, 7:13 pmHi you have contact no for UD? I am looking for KC and wardrobe as well. Thks


This post has been edited by bigmamma: Mar 15 2011, 07:13 PM

UD mentioned they are booked till third week of april. Has yet to hear from them on my revised design after the site visit.... wondering if they can cope with the many orders....

can u quote me for:-

1. wet kitchen 6'5"base & wall unit(42'1/2"H) x 9' base unit w/o concrete top
2. dry kitchen 8' base & wall unit (42'1/2'H + lift up unit) with solid surface, 7' tall unit 102"H, 3'wall unit x 24"H

melamine hard board & glass door. thank you.

Let me hv the contact as I am not in a hurry to make yet as house is currently under reno.

UD's contact.


BTW...they have installed my solid top!! yippee!! Photos will be uploaded later.

Anyone deal with Meridien Design??? Pls advise.

Details:
weight: total 17' (8'+9')
Height: 11'
material: wood=Nyatoh Wood ; door=blur glass

can anyone code it for me?how much it could be??
Thanks alot!!

Looks great!
Will be contacting you after my reno is done. Hope you won't be too busy with so many orders

Finally completed. They installed my solid top yesterday

Hi Erny, I have an existing concrete counter top with tiles. Is it possible to replace the tiles with granite top without demolishing the whole counter?
Also, the concrete counter doesnt have any cut-out for the cooking hob. Can this be cut also without rebuilding a new counter top?




Attached thumbnail(s)

There is a drop down part for on your concrete table, i think that is the part to put your cooking hob on top (old fashion type), if you remain that area as your cooking place, and open a hole for that, your cooking lever will be very low already.

I wanted to share mine :

Wardrobe(small one, my room not so big)

was Now

KC(granite table top)

was Now

Total Cost is RM8k only.

Gonna attend a furniture exibition in china tomorrow. Will back to KL next week. So wish u all a great weekend there! Cheers!

Let's share some new wardobe~

---

Added on March 17, 2011, 6:36 pm











This post has been edited by Erny_Looi: Mar 17 2011, 06:36 PM

Please share your KC contractor company name and contacts. 10q

Hi, I'm Erny~

U can just add a concrete stand below the drop on right side, then hack the stove area and reconnect it. Then u will have a flat table top. So that u can have a granite top or solid surface on it. But u will see the thickness of the granite table will be a bit thicker than normal one coz it have to cover the concrete table.

---

Added on March 17, 2011, 11:05 pmMeredere, nice! Should go and snap some photos, wanna keep it in my album. Haha!

This post has been edited by Erny_Looi: Mar 17 2011, 11:05 PM