they originate from 2 gtx 275.

hi guys.. i just got my galaxy gtx 275 accelero extreme tri fan oc.. i want to know what is the temperature i highlighted in the img below.. cos i notice after i tried oc it a bit it will reach to around 115centigrade..



This post has been edited by ToddStarz: Apr 29 2009, 05:12 AM

tod remember the rams i was telling u about

the patriot viper 6gb 1600mhz CL8 (micron d9JNL) blue copper heatspreader+black pcb

karom is bulking it for rm4++

it comes with xmp freaking worth it.

"the vddc slave temps are the temperatures of the 3 pwm phase controllers of the card" W1zzard



This post has been edited by metsatsu: Apr 29 2009, 07:06 AM


Attached thumbnail(s)

i read review about GTX275 and GTX285
is not much different
price also quite high for GTX285

Anyone has any idea of how far can Palit GTX295 go?
I RMA my MSI GTX295 for Palit GTX295 and I was thinking of OCing it once I get it back.

i think not much different , sin all gtx295 are refrence board, only sticker different

No difference. They are all reference cards. If u wanna make a diff, increase the vcore and oc the hell out of it

how much is the max tolerable temp there..

technically u shouldnt push them more than 80-85C.

also the temp sensors themselves are not accurate. so hard to judge.

phase . the more phase u use the less stress u have but u will loose in current flow.
higher frequency will get better more accurate current. and will even lessen the temp.

ok its getting weird.. sorry for the noob questions.. cos i dont want to oc my gpu without clarifying somethings..
i tried to run furmark stability test and the VDDC temps keep increasing.. so i stop furmark around 5 minutes.. heres the ss
at idle..

just start furmark stability test

around 4 minutes

VDDC current 76.5A ? thts hell lot.is it because of the custom tri fan cooler?

mine is only like this



gtx260 with stock cooler overclocked to *see sig*

tht ss is taken when idle

This post has been edited by ZeneticX: Apr 29 2009, 04:10 PM

nope.. at idle is the 1st pic..

oh ok my mistake since u bring up this issue of the VDDC temp i gonna test mine as well now.i nvr paid to much attention to those 3 temps

---

Added on April 29, 2009, 5:29 pmbtw wan to ask is it normal to see flickering during the benchmark test of furmark?i ran it and once it comes into 2 min mark flickering start to appear

This post has been edited by ZeneticX: Apr 29 2009, 05:29 PM

GT200 aftermarket cooler problem? I also saw a news that report the hr03gtx got vrm temperature hot until burn the display card problem, then thermalright response said that furmark is not a normal application and they recommend atitools.

This post has been edited by nncl: Apr 29 2009, 05:42 PM

btw nncl i already flashed ur bios into mine minus the clock settings,which means i reset them to default but keep the voltage setting.tried another oc just now but didnt went good,so yea i guess im done with my card

furmark wasnt meant for commercial gc

its just to test loads on gpu power
it doesnt test artifacts or overclocking stability

so if any artifacts,flickering appear during the test i should take notice of it or just ignore it?

May be your card nearly air limit already

---

Added on April 29, 2009, 5:50 pmwanna make you a 1.18v bios try?

This post has been edited by nncl: Apr 29 2009, 05:50 PM

i will get it frm u when i have the sudden interest to oc agn .right now im happy with my clock

btw y u can set ur voltages so high?my highest is only 1.15 ,jz nw i tried ur bios and the highest also only can reach 1.16

This post has been edited by ZeneticX: Apr 29 2009, 06:52 PM