If you could elaborate, maybe some of us could help.

Thank you arthos7 for sharing. I can confirm that with g I am getting stronger and faster connection. Video streaming requires less frequent buffering now.

tercupee,

i dont really use wife

Is this intentional?

I suppose one could be tempted to do just that after getting an Omnia

I am not sure this whether this info is useful to you. I have done a lot of roll back of firmwares on other electronic devices. A firmware usually contains its version code and when you try to update a firmware your device will compare what is already installed to the firmware you intend to install. The device will not allow you to install an older version of firmware. This is what to are facing now.

However there is a way to get around this. All firmware codes are written in Hex decimal. What I have done previously ( not on Omnia firmware) is to use a Hex Editor to edit the version of the older firmware you wish to install to appear to be a newer version, thus tricking the device to think that you are installing a newer version.

I have briefly checked the HJ1 firmware with an Hex Editor but were unable to find the location of the version code in the firmware. If I have more time later I will try again.

Check this out, Malaysian teaching American how to do it; http://www.avsforum.com/avs-vb/showthread.php?t=988167


I am still trying to figure out the correlation between HH3, HJ1 and HK1 firmwares. These are the only 3 firmwares I have.

P/S Could not find any correlation during lunch time. Will be traveling after this.

This post has been edited by DrWho: Dec 15 2008, 02:02 PM

Another Accelerometer game, Teeter, by speleomaniac @ Modaco. Unzip and install cab file. Copy the 3 other files to the Labyrinth folder. Soft reset and enjoy.


Attached File(s)
 Teeter.zip ( 1.48mb ) Number of downloads: 219

......and at such early hour as well....

With a screen size of 3.2 inches and 400X240 pixels you can hardly see a single pixel. Unless the video source is of high resolution 720 or 1080 lines, which I don't think PPC media player is capable of playing, you will not notice any difference even if the screen is VGA ,ie 800X480.

I found the rmvb codec for WMP sometime ago but have not played a rmvb video as yet, thus I do not know whether this works.




Attached File(s)
 RMVB_codec.zip ( 576.15k ) Number of downloads: 42

In theory Sprite Backup or Spb Backup could backup all data including system files and registry. Do a complete backup and hard reset and restore from backup, you will have all data intact like before your hard reset.

Install the Garmin program and map at My Storage or Storage Card. After flashing you just need to install the Garmin program at the same location and it should work.

Instructions to install Garmin is indicated on Post #1.

I can confirm that there is no problem with Omnia installed with Garmin and Mapking together.

What is your device Storage capacity? It should be at least 10MB to prevent hanging.

I don't think firmware is the cause. Did you use Task Manager to exit all Programs rather than just close?

I followed the installation instructions for Garmin provided by damagedigital as in Post#1. Goto his Maps collection for the hasslefree map.

You should elaborate so that we know the exact problem you are facing. Maybe then, someone would be able to help.

Many forum is advocating this. Check out this site for more tweaks:

http://knguyentu.com/wordpress/2009/01/ver...i900-unleashed/

Enjoy

No need to send to FMG. A Hard Reset should sove the problem so will updating the device with a new ROM. Hard Reset is the easiest but make sure you backup your data eg contacts etc etc.

If Hard Reset or ROM flashing cannot rectify the problem, only replacement of hardware will. Hard Reset will eliminate problems caused by softwares.
If you want to avoid Hard Reset, try this:

http://knguyentu.com/wordpress/2009/01/ver...i900-unleashed/

Goto Improve Screen Calibration Accuracy. This requires you to edit your registry, which is more dicey if you are not familiar with it.

How about "Disable all other running programs at your PC"?